Jump to content
SAU Community

Recommended Posts

Hey guys, it's probably been covered, but for the life of me can't seem to figure it out and google isn't really helping.

The car will start fine and run fine, but after 5 minutes the whole car will seemingly die and the battery light comes on, its a new battery but has been charged and I didn't have this problem before, but however when the car has had that hickup it seems to be fine afterwards, just find it weird that i lose all power and engine cuts out, could it be alternator and or blown fuse causing the car to be shitty?

(Also this only happens first thing in the morning, in the afternoon on the way from work it has no problems at all)

Any advice is much appreciated :) 

Link to comment
https://www.sau.com.au/forums/topic/473759-r33-randomly-dies/
Share on other sites

11 minutes ago, r34.rory said:

Check the alt belt, could be worn and slipping or not enough tension maybe.

My R34 battery light came on last year and died turned out the belt for alternator shredded and flew off.

f**k,I'll have a look, i know my battery went dead a month ago but fully charged it and didn't have an issue till now, will check when i get home

Look, if the engine is just stopping, then either it has a mechanical problem / vacuum leak / fuel supply issue etc etc, OR it is simply losing electrical power to something vital.  These vital things include the coils, for example, and the ECU.  The Nissan engine management system is known by their abbreviation ECCS.  The ECCS relay is the relay that provides power to the ECU.  Its operation is a little complicated, but the overall view is that when you want the engine to be running the ECCS relay needs to be powered up.  Like all relays, they can get flaky.  When they do, they can drop power to the ECU, which tends to have sudden consequences.

You can find the relay near the ECU.  If you don't know what you're doing, you shouldn't stuff around down there, because you can make things worse.  If you had put the words "ECCS relay" into google, you would have found all the thousands of words that have been written on here across the last 25 years, in which you will find much wisdom.  The O2 sensor and the TPS are not likely to be responsible for your stoppages.  The CAS might.  The fuel pump might, just.  A broken wire in a loom definitely could.

Then it's not your alternator. If a dead alternator caused the engine to stop then the battery power would be drained. You wouldn't be able to start it back up.

GTSBoy noted many things to check. Start there as I reckon he's on the money.

As a side, I had a similar issue with intermittent stalling out of nowhere. After some trial and error I narrowed it down to my fuel pump relay - it's rare for these to die but it happens. I replaced mine and I was sweet, no more problems.

  • 3 weeks later...

Hey mate! Cleaned the iacv, also had a small vac leak on the std intercooler piping, but other than that it still struggles some mornings and still feels like it wants to stall, but I couldn’t find anything wrong in the wiring, even my mechanic couldn’t find anything. 

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...