Jump to content
SAU Community

Recommended Posts

Hey guys, it's probably been covered, but for the life of me can't seem to figure it out and google isn't really helping.

The car will start fine and run fine, but after 5 minutes the whole car will seemingly die and the battery light comes on, its a new battery but has been charged and I didn't have this problem before, but however when the car has had that hickup it seems to be fine afterwards, just find it weird that i lose all power and engine cuts out, could it be alternator and or blown fuse causing the car to be shitty?

(Also this only happens first thing in the morning, in the afternoon on the way from work it has no problems at all)

Any advice is much appreciated :) 

Link to comment
https://www.sau.com.au/forums/topic/473759-r33-randomly-dies/
Share on other sites

11 minutes ago, r34.rory said:

Check the alt belt, could be worn and slipping or not enough tension maybe.

My R34 battery light came on last year and died turned out the belt for alternator shredded and flew off.

f**k,I'll have a look, i know my battery went dead a month ago but fully charged it and didn't have an issue till now, will check when i get home

Look, if the engine is just stopping, then either it has a mechanical problem / vacuum leak / fuel supply issue etc etc, OR it is simply losing electrical power to something vital.  These vital things include the coils, for example, and the ECU.  The Nissan engine management system is known by their abbreviation ECCS.  The ECCS relay is the relay that provides power to the ECU.  Its operation is a little complicated, but the overall view is that when you want the engine to be running the ECCS relay needs to be powered up.  Like all relays, they can get flaky.  When they do, they can drop power to the ECU, which tends to have sudden consequences.

You can find the relay near the ECU.  If you don't know what you're doing, you shouldn't stuff around down there, because you can make things worse.  If you had put the words "ECCS relay" into google, you would have found all the thousands of words that have been written on here across the last 25 years, in which you will find much wisdom.  The O2 sensor and the TPS are not likely to be responsible for your stoppages.  The CAS might.  The fuel pump might, just.  A broken wire in a loom definitely could.

Then it's not your alternator. If a dead alternator caused the engine to stop then the battery power would be drained. You wouldn't be able to start it back up.

GTSBoy noted many things to check. Start there as I reckon he's on the money.

As a side, I had a similar issue with intermittent stalling out of nowhere. After some trial and error I narrowed it down to my fuel pump relay - it's rare for these to die but it happens. I replaced mine and I was sweet, no more problems.

  • 3 weeks later...

Hey mate! Cleaned the iacv, also had a small vac leak on the std intercooler piping, but other than that it still struggles some mornings and still feels like it wants to stall, but I couldn’t find anything wrong in the wiring, even my mechanic couldn’t find anything. 

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...