Jump to content
SAU Community

Recommended Posts

so i need to remove the radiator from my 250t rs four which has been converted into a 6 speed manual out of a 350z.

it is still using the stock radiator so it has lines going into the radiator for cooling the transmission from when it was an auto.

So, are the transmission lines connected at the bottom to the two brass fittings? (photo attached for reference)

 image.png.f9559440d6bec7d17250bea117615f10.png

these have nothing attached to them so i am not sure what they are for, other than that.

i think i may be mistaking the transmission fluid lines for something else as the lines I want to remove  are on the passengers side of the radiator and coming off the side of it.

this photo shows the lines i need to remove. 

Untitled.thumb.png.f0c8be19aa469f5b903a8fb805c4e4c1.png

 Any help would be appreciated. 

cheers

 

 

Link to comment
https://www.sau.com.au/forums/topic/474157-m35-transmission-fluid-cooling/
Share on other sites

You no longer have CVT (continuously variable transmission) so not sure what you are worried about buddy. I have put a 300zxTT auto in my skyline and have installed a large cooler and i'm not using the little standard trans heater in the standard radiator. Maybe you are overthinking this.

Edited by Rusty Nuts

The new radiator you have is an automatic radiator, it is common practice to supply this radiator as a replacement part for manual vehicles, It saves stocking Two types of radiator in their store.

Edited by Rusty Nuts

If you want to keep air conditioning remove that single fan, then remove that condenser and I hope there is a fitting on your new radiator to bolt it back on, Then reassemble and reconnect the lines from the compressor and take to aircon specialist for regas.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...