Jump to content
SAU Community

Recommended Posts

Hey guys
New to this forum, recently bought a V36 350gt Type SP, and it has what looks to be an antenna/parking pole, in the front bumper on the passenger side.

I've spent the last hour or so looking reading through owners manuals, but no luck.

Does anybody know how to retract it? Currently it's up whenever the car is on and I'm finding it a bit annoying.

Attached are a couple of pics. Any help would be appreciated

Cheers!

37127031_10157099074619367_1411586141936680960_n.jpg

37198249_10157099074644367_1709403031121952768_n.jpg

Link to comment
https://www.sau.com.au/forums/topic/474506-jdm-v36-antenna/
Share on other sites

12 hours ago, The Max said:

What's the rectangular cutout in the corner of the bumper bar?

It's a front camera, there's one in the same spot on the other side of the bumper too. I imagine it's handy for inner city driving in Japan, I haven't personally found them very useful lol

Link to comment
https://www.sau.com.au/forums/topic/474506-jdm-v36-antenna/#findComment-7881282
Share on other sites

Nice! Could be handy for parking up close to a wall or something.

Anyway, if the dude who installed it hasn't implemented a neat little switch in the cabin, probably just worth getting in behind the bumper bar and disconnecting the power connector going into it.

Link to comment
https://www.sau.com.au/forums/topic/474506-jdm-v36-antenna/#findComment-7881283
Share on other sites

Those cameras are for pulling out at blind junctions generally between buildings.. just stick the nose of the car out rather than the entire engine...

My car has an aftermarket one mounted on the number plate. More useful, I reckon, and can also be used to park 2 mm. from the car in front....:banana:

  • Thanks 1
Link to comment
https://www.sau.com.au/forums/topic/474506-jdm-v36-antenna/#findComment-7881317
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...