Jump to content
SAU Community

Recommended Posts

Hey I own a skyline R34 2000 sedan and i have recently been having trouble with my steering wheel shaking when I reach 100kph.

The car as had 1 alignment done and been balanced twice...neither fixed the problem :/

The left tie rod has been replaced also as that was on its last legs but still didn't fix the problem.

i don't believe it is the tyres as it drives pretty straight without dramatic pull to either side of the road and no obvious wear is noticeable but due to me not being a mechanic in any way, I could be wrong. 

any suggestions on how to fix this problem would be highly appreciated as I am puzzled to what the problem could be.

thank you. 

 

Link to comment
https://www.sau.com.au/forums/topic/474529-steering-wheel-shake-at-100kph/
Share on other sites

Usually when you feel the shake in the wheel, its an unsprung issue (as in, wheel side of the springs, not car side)

sprung weight issues are usually felt through the floor seat and pedals.

So the first thing you need to do is take the car for a drive on a nice smooth road with the radio off, and pay close attention to what you can actually feel, so you can tell an expert clearly.

In my experience what you describe sounds like a wheel or tyre out of balance, possibly  even a wheel bearing (although you would see this immediately when doing an alignment)

Stick your head into the back of the wheel, and see if you can find any evidence of wheel weights not being where they should be.

I would just jack up the car, spin and wobble the wheel. 

All 4 shouldn't take more than 10 minutes.

As for "techs" picking up a issue during a alignment, that's not something I would lay a bet on.

I have lost wheel weights when cleaning the rims, usually because the "techs" just stick it on without any cleaning or prepping the surface.

2 hours ago, mlr said:

 

I have lost wheel weights when cleaning the rims, usually because the "techs" just stick it on without any cleaning or prepping the surface.

Damn right. New wheels, took it back to shop, got rebalanced. Witnessed new weight on there...had fallen off by time i drove home.

On 7/18/2018 at 10:30 AM, mlr said:

I have lost wheel weights when cleaning the rims, usually because the "techs" just stick it on without any cleaning or prepping the surface.

I always remove my wheels and clean them the day before my appointment with the tyre shop... they do notice things like that.

 

 

I paid a tyre shop $200 to adjust the front end of my car to the specs I wanted.

After two hours, the "tech" absolutely fked the front up. I took it home and adjusted it by eye in 10 minutes to bring it to a more driveable state.

Can't pay anyone to do anything any more, unless proven otherwise.

3 hours ago, niZmO_Man said:

I paid a tyre shop $200 to adjust the front end of my car to the specs I wanted.

After two hours, the "tech" absolutely fked the front up. I took it home and adjusted it by eye in 10 minutes to bring it to a more driveable state.

Can't pay anyone to do anything any more, unless proven otherwise.

I use JAX at Liverpool, usually $60 for full alignment to my specs.

Only issue I ever had was the steering wheel was off center once, they fixed it straight away. 

With the laser gear it makes doing an alignment (EDIT: should be) idiot proof.

Hell, I've watched the guys do it so many times I reckon I could give it a crack, it ain't rocket science.

Did you get the problem sorted?

9 times out of 10 a wheel wobble is wheel and tyre related, some tyre shops will be good and tell you if there is a problem, others won't.

Causes can include (but are not limited to)
- Wheels bent
- Old tyres
- Tyres not round (also see: cheap tyres)
- Tyres unevenly worn

Do you have half decent tyres on the car? How old are your tyres? Have you tried rotating wheels front to back? (if a wheel is slightly bent, it's better to have it on the back).

The other 10% of the time as Ravi said it could be related to other parts of the steering/suspension.

On 7/20/2018 at 2:11 PM, mlr said:

I use JAX at Liverpool, usually $60 for full alignment to my specs.

Only issue I ever had was the steering wheel was off center once, they fixed it straight away. 

With the laser gear it makes doing an alignment (EDIT: should be) idiot proof.

Hell, I've watched the guys do it so many times I reckon I could give it a crack, it ain't rocket science.

One day I'll wake up early on Saturday and take my car there. I had a mate get alignment on two of his cars there so good reviews there.
I guess I was ill-informed when I handed over my cash. Lesson learnt.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...