Jump to content
SAU Community

Recommended Posts

First pic its the oem boost solenoid. Do you have some sort of boost controller installed?

Second one looks to be somekind of diy switch. Could be for anything really. Possibly a power switch for aftermarket gauges, lights or something like that. Only way to find out is to follow the wires

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891059
Share on other sites

First picture is a boost solenoid which may have been connected some type of boost controller before it was unplugged.

Second photo is a on/off for something as others have said - if you want to find out take it out and then follow the wiring. My guess is it was for something boost related but has since been removed. Very stealthy to have it mounted by the door.

Third photo is a fire extinguisher holder. Most Skylines (all, if I’m not mistaken) came with portal fire extinguishers but most have been removed.

Cheers.

  • Confused 1
Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891068
Share on other sites

11 minutes ago, adey88 said:
2 hours ago, FedBpy2018 said:
Is this thing normal? 
20181114_202509.thumb.jpg.0c90dde661037708166d582c79ae0439.jpg

I believe that's for a flare (not fire extinguisher) as required by law in Japan.

Actually, now come to think of it...I think you correct. Then some people place fire extinguishers there but originally yes it was a small black flare.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891074
Share on other sites

1 hour ago, Robocop2310 said:

Actually, now come to think of it...I think you correct. Then some people place fire extinguishers there but originally yes it was a small black flare.

People don’t put fire extinguishers there because it will be hard to reach while in the drivers seat, usually it’s on the right hand side of the passenger foot well or under the drivers/passengers seat. Also the flares are red.

 

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891079
Share on other sites

5 minutes ago, Milkmun said:

People don’t put fire extinguishers there because it will be hard to reach while in the drivers seat, usually it’s on the right hand side of the passenger foot well or under the drivers/passengers seat. Also the flares are red.

 

Right, you are (photo of flare on same spot).

images?q=tbn:ANd9GcSvXAHjllvKPsvxpO5YHvo

 

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891081
Share on other sites

Since you are not using the stock boost controller you must have an alternative. The simplest would be an R32 actuator. Trace back from your actuator to see where the line goes and you will find an aftermarket controller if fitted.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891090
Share on other sites

I followed the wires from the actuator they lead inside the dash through the firewall and cant follow from there, this sunday im going to take the dash apart and find it, has anyone got a guide to do it? If it was a car i normally work on i could take it apart in less then 5 mins lol, im guess for this it will take a few hours to pull apart and put back

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891151
Share on other sites

14 minutes ago, FedBpy2018 said:

I followed the wires from the actuator they lead inside the dash through the firewall and cant follow from there, this sunday im going to take the dash apart and find it, has anyone got a guide to do it? If it was a car i normally work on i could take it apart in less then 5 mins lol, im guess for this it will take a few hours to pull apart and put back

That's a factory boost solenoid with factory wires that will lead back to the factory ecu. Hardly worth chasing, certainly don't pull your dash apart to solve this non mystery.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891153
Share on other sites

3 minutes ago, FedBpy2018 said:

So dont bother using it then?

Well, that depends on what other boost control you have.

 

Also, there is an obvious misunderstanding as to what terms is being used here.  The item in the photo is the boost control solenoid, as others have said.  The "actuator" referred to by Kiwi is not that solenoid.  He meant the actuator that is mounted on the turbo that pneumatically pushes on the wastegate lever.  Not the same thing at all....although, obviously, related.  All part of the boost control.  Anyway, there are no wires on the actuator.  There wires on the solenoid are as Ben said.  You should follow all advice given.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891157
Share on other sites

From what i can see inside the car there is no other boost controller, also what causes a door window to tilt towords the inside of the car? Photos attached, the purple line on the window is the window hitting something on its way up so i dont use it but previous owner did, the first photo is what a owner had done to bypass the solenoid

20181115_203504.jpg

20181115_203621.jpg

20181115_203703.jpg

Edited by FedBpy2018
Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891163
Share on other sites

Unless that's an RB20 actuator (and I can't be stuffed searching the part number to check).....then you have a whole 5 psi and your car should be as slow as all f**k.

The window is easy.  The stuff inside the door that keeps the window aligned (so, either the runner channels/rollers or the felt pads near the top) are stuffed.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891165
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...