Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm in a 70's apartment complex and I really wish I could hand wash my Skyline.  I currently take it to the $1 wash places.

I do have power but I have no water/tap nearby.  Also, I don't want too much soapy water run off in the common driveway area, I'm sure a little is fine though.

I'd like to know what type of high pressure washer would be best.  I saw at Aldi there are some available that can source water from a bucket via a hose, and also at Bunnings there are these things these Ryobi 20L bladders.

My questions are - how much pressure would I need to give my car a good wash?  These things range from $99 up to $499 and brands Ryobi, Karcher, Gurni, etc.

This Ryobi 1800W 2000PSI for $129 looks good, although it doesn't look like it can use a portable water source.

Questions:

  1. I've noticed some have a soap tank and some a separate soap bottle attachment - either of these good or should I just stick with soapy water in a bucket?
  2. How quickly do these units use up the water?  I mean, if I had a standard household bucket or the 20L bladder, would that be enough for a good wash or would I need to keep refilling it?
  3. What would be the minimum power / PSI I would want for a reasonable clean?
  4. Are any of the brands much better / worse than the others?
  5. Any recommendations on a mains powered portable water version?

Thanks!!

Edited by Haxorz

There's also the waterless wash and wax stuff. Depending on how much you trust the science behind it it may be an option. Seeing people use it on Ferraris and Porsches for years has made me believe it works fine for my 34.. 

/prepares to be brutally murdered

You don't need any pressure at all.  Any pressure washer will do more than enough.  You only want to wet the car prior to bucket&glove wash, then gently rinse it off.  High pressure concrete cutter type washes are for boats and bro-dozers, not nice cars.

Ok cool.  Just the most basic one then.

My current problem is finding a basic one that draws water from a bucket - the only one with the portable water source that I can see is the high end V36 battery powered Ryobi for $349 - 499...

Wish I jumped on the Aldi one sooner.

I like power washers, not paint stopper power held close though.

I use a little Karcher that has a foam attachment and hose that sucks u p car wash.

 

1st, I foam the car and let it sit

I then Karcher the foam of to remove all dirt and grit that a hose wo u ld leave, I get in nice and deep like....

 

I then hand wash and dry with bath towels.

 

Gee that ONR stuff looks awesome.  Does it really work?  I've seen a few YouTubes and it's people using it to clean already clean looking cars. 

Mine is black, parked outside and looks TERRIBLE and filthy after a downpour.  Hard to imagine it turning that into something clean with little friction based 'washing'.

I wouldn't use a spay on wipe off stuff if you like your paint, hell, I foam and pressure wash my car before I use my microfiber wash cloth.

 

I've done alot of work with soils, in construction, with that alot of soil testing and research.

 

Alot of that fine dust you see is fine sand and silt, both are bulky materials, whilst it is small it does scratch shit up good.

But, don't let that get in the way of good marketing

 

images.jpeg

Having lived with a Skyline in the inner city, I'd be less worried about micrometer scratches from dirt and more worried about people who employ "touch parking" techniques.

  • Haha 2

It does work yes. But generally recommended for light to medium dirt buildup, so I wouldn't use the method on a really filthy car. 

When i was driving my S14 every weekend, I would clean it every Sunday night with a quick detailer and 2x clean microfibre cloths - never had issues with swirls or scratches

22 hours ago, junkie said:

It does work yes. But generally recommended for light to medium dirt buildup, so I wouldn't use the method on a really filthy car. 

Cool, I thought so.

Mine gets really really filthy with trips out the country.

I was thinking of combining both, a cheapie $99 Karcher pressure washer , this $45 suction hose kit (which is a rip off but required because it has the fancy valves in it to stop sucking in air and allow it to work against gravity) to first spray it all down and then use the rinse-less wash to 'wash' the car and perhaps a powerful air blower to dry it.

I just can't see the rinse-less wash washing off splattered on bugs, heavy dirt and other hard to remove things like that.

Combined with buckets and sponges it looks like I'd be spending near $200 just to wash my car at home, now I know why I've been using the $5 do it your things.  Went to wash it at my nearest one but the queue was 3 cars deep, one of the cons of living inner city.

The rinseless wash stuff feels like magic when you use it though. Now I don't know about the chemicals but the claim is that it breaks the bonds down between the paint and the dirt itself. It "feels" like it dissolves it instead of wiping it off. So quite often you will spray something stubborn and it wipes right off, which is... skeptical.

Things do exist for bug stuff though - Pretty much the hardest things that exist to clean off a car really is good ol dried up splatters after going for a drive in the country.

That said, the rinseless wash stuff is often regarded to as "the wash between washes" so to speak. The bonus is if you do it once a week it literally takes ~5 minutes. Hasn't really been in use long enough yet for someone to say "I did this once a week for 10 years and this is what happened to my paint" yet.

  • 2 months later...

Like others, I have been using Meguiars waterless wash for a few years now and am sold on it.  I wash the car properly about every 3rd or 4th time, but in between I use the Meguiars.  An added bonus is the 'as good as wax' finish it gives you,  And I can do my whole car in 15-20 minutes.  Only thing I do before starting is to use a dust mop/brush on the car first, a 5 minute job.

And you need so little of the waterless solution that I am still using the same bottle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...