Jump to content
SAU Community

Recommended Posts

Hi All, Couldn't find anything on this topic so hoping someone out there can help.

My cluster stopped working so I had to replace it with a stock second hand one. My car has around around 75,000 km and the replacement cluster has 51,000 km on it.

Wanting to know if there is a way to increase the reading so that my odometer stays consistent?

Edited by R33_Kris

Haha yeah there is that option but I don't have the time.  No service history, so would be good to adjust it somehow.

In NZ the km's get registered on a site called CARJAM so would show up as an inconsistent odometer if I left it how it is now.

Edited by R33_Kris
29 minutes ago, R33_Kris said:

In NZ the km's get registered on a site called CARJAM so would show up as an inconsistent odometer if I left it how it is now.

And as long as you're open with it and there is some way to note it in CARJAM, there really shouldn't be any problem.

Your physical solution is to go buy a cheap Chinesium cordless drill, connect it to the speedo drive (pulled out of the gearbox) and sit the car in the garage with the trigger cable tied until it has done 24000km. That would suck, but it would work.

Your electronic solution is to make an Arduino to output a sine/triangle wave of about +/-1V and pulse it at whatever frequency is broadly equivalent to 300 km/h and let it run until the odo winds on 24000km. That's about 80 hours, or a long weekend.

  • Like 1

Hmm, sounds like there's no easy approach to this. Might just have to document the change and live with the 24,000 km decrease on CARJAM. It doesn't bother me and to be honest I'd live with it if I was going to keep the car forever, but I will eventually be selling it to buy a house in a couple years and worried it might hurt the resale value.

Is what it is, I guess it would be OK if I keep the broken cluster as proof. Would've been nice to keep the records clean though.

Yes, in regards to resale: all you can do is keep the old cluster, any documentation (take photos) and be up front about it.

I looked at a few cars that nismo cluster swaps, it didn't phase me (and shouldn't phase an educated buyer) as long as there's documentation to explain the discrepancy :) (y)

Remove the cluster from the car, remove the odometer from the cluster remove the speedo odometer and you can pretty much use your fingers to move the dials around to get to the position you require 

  • Like 1
  • 3 weeks later...

Email LTSA with the previous kms, the new kms, why you swapped it and a receipt for the new cluster.

It'll still show inconsistent speedo on Carjam but will be legal, Auckland Instruments or Robinsons could probably wind it forward otherwise.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...