Jump to content
SAU Community

Recommended Posts

Do you have an IAT sensor? It's worth checking it to see. You may be suprised how little gap you actually need to flood your engine with hot air. (I tape up my airbox for a reason) :p

10 minutes ago, Kinkstaah said:

Do you have an IAT sensor? It's worth checking it to see. You may be suprised how little gap you actually need to flood your engine with hot air. (I tape up my airbox for a reason) 😛

Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise

But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy

  • Like 1
20 hours ago, The Bogan said:

holidays are continuing now as we are currently chilling at the Beachcomber in Toukley, after taking the coast roads from Sydney in the MX5, top down all the way, Toukley is where I spent a good deal of my youth holidaying during the summer months, there's lots of reminiscing going on,  and lots of beaches and old houses to visit

I hope u were never staying at that beautiful caravan park that used to be across the road from the Beachcomber! 🫣

  • Haha 1
1 hour ago, Watermouse said:

I hope u were never staying at that beautiful caravan park that used to be across the road from the Beachcomber! 🫣

Nope, I stayed at some dumps in my youth, but now it's real nice or nothing 🤣

Currently kicking it at The Entrance 

  • Haha 1

Also discovered that the NC ride height needs to come "UP" at least 10mm to clear some newly found speed humps up the central coast 😫

Job for tomorrow, I'll start at 10mm up other both ends from where it is now and hope that's enough for our next adventure 

  • Sad 3

After some googling of various websites IRT the best ride height for correct geometry I ended up going,  hub to guard, 330mm in the rear and 345 at the front, these heights came from Flyin' Miata in the states as what they recommend (13" rear, 13.5" front)

The rear needed to only come up 5mm, but the front came up 15mm

Overall it is around a 25mm drop from OEM ride height, doesn't look all 4x4, and hopefully should be enough height to clear those pesky speed humps

20241119_121558.thumb.jpg.e774e735b70e5666534a66c08dd1389e.jpg

I have lost around 0.5° camber on the front, and around 0.2° in the rear, I have no idea about what it did to toe settings so I'll look at a new alignment next week to get it set up how I want, zero rear and a little in at the front

I've also stripped the new intake and am currently cleaning and preparing the alloy for some paint, I've headed into work to do it as I can use the ovens in the soils lab to cure the wrinkle paint at 90°c

17319784984711155768368953948182.thumb.jpg.36a59fc12becffc8462b0689832c414d.jpg

Jackie has banned me from using the oven at home for stuff like this....🤣

 

 

  • Like 2
  • Haha 2
31 minutes ago, The Bogan said:

After some googling of various websites IRT the best ride height for correct geometry I ended up going,  hub to guard, 330mm in the rear and 345 at the front, these heights came from Flyin' Miata in the states as what they recommend (13" rear, 13.5" front)

The rear needed to only come up 5mm, but the front came up 15mm

Overall it is around a 25mm drop from OEM ride height, doesn't look all 4x4, and hopefully should be enough height to clear those pesky speed humps

How much clearance is under the car?

We have speed humps being added everywhere around me. Faster than they fix the potholes, thats for sure.

17319828574433228892526522486878.thumb.jpg.f547414b79707ca9623be6f24c842ace.jpg

39 minutes ago, PranK said:

How much clearance is under the car?

We have speed humps being added everywhere around me. Faster than they fix the potholes, thats for sure.

I'll measure it up at the lowest point later and post it up

Currently painting, with the oven all warmed up to 93°c

 

2 hours ago, PranK said:

How much clearance is under the car?

We have speed humps being added everywhere around me. Faster than they fix the potholes, thats for sure.

Lowest point on the car is 105mm now, so just legal and hopefully high enough to clear

After paint, much happier with how it looks

20241119_153323.thumb.jpg.daa27ef23b310b55dd7dc15c792a3359.jpg

Before looked real 😝

20241116_151909.thumb.jpg.a97e3db66ca56c3bfbf2d70098fe07a8.jpg

 

  • Like 4
9 hours ago, Milkmun said:

Nice work on the paint.

Those 3 studs are long as. 

Yeah, the plan is to just put some black rubber vacuum line caps over them to "hide" them a bit

I don't want to trim them in cause I need to put the OEM box back on at some stage

  • Like 1
  • 2 weeks later...

The MX5 has had some annoying rattles in both front doors over bumps

So I installed fancy pants door bushings, which stopped all of the rattles with the windows up, but........with the windows down there was still rattles, so after some googling,  and a chat with MX5 Mania, I got some new door to glass weather seals, all the rattles, windows up, or down, are gone now

Shout out to MX5 Mania, the weather seals were on sale, and when I head to Dural to pick the up they even fitted them for me for free

I did see a "really" nice Blue NA sitting out front

20241128_110632.thumb.jpg.c4a503807d0e587859704e4415f25a51.jpg

 

and this Black NC PRHT that looked like it has sat in the sun for its whole life and never had a wash, the clear coat was non-existent, an it looked horrible, really horrible, but, it had a nice turbo kit with over 200kw, the thing went like a cut snake, bagging the rears through the gears and dosing like a champ 😍

But, as I've always stated, I am keeping my NC na, I'm happy with the current power the car makes

In other news: MX5 Mania do a drive in drive out turbo kit, the only minor additional part recommended for boosting my car, as it sits now, is a oil cooler, and that bonnet vents are definitely required for track use

Aftermarket version look a bit to "racecar" spec

images(51).thumb.jpeg.4f56a13469549e0dbc7498285d5ddaef.jpeg

I wonder how Focus RS bonnet vents would look?????

images(50).thumb.jpeg.d24a005605b8e668cc2aac4751818e03.jpeg

  • Haha 1
47 minutes ago, MBS206 said:

January or Feb is it booked in for turbo fitment?

No......not yet

Minister for War and Finances has stated that the Commodore has to go first

Not that I am going to modify the NC any more than what it is already modified now.....

1 hour ago, The Bogan said:

No......not yet

Minister for War and Finances has stated that the Commodore has to go first

Not that I am going to modify the NC any more than what it is already modified now.....

So you're now accepting offers of 10% more than the cost of the turbo kit fitted?

  • Haha 1
10 hours ago, r32-25t said:

Bahahahaha had a feeling it was only a matter of time till a turbo was on the radar 

 

1 hour ago, GTSBoy said:

Foreshadowing was never so easy.

My hold point for future mods is that I want a OEM detachable hard top first, but, finding one is a pain, MX5 Mania are looking for one for me, but, as hens teeth are more common, finding one in Australia is proving problematic 

I can get a OEM one from overseas, hell, you can still get new ones in 'Merica, but, shipping is a absolute killer and I cannot justify the cost, or the risk of it being damaged during transport

As for the aftermarket hardtops, whilst they do the job of being a hard top, and are fine for a track car, they don't seal well (read: leak like a sieve in the rain), and you need a plastic/poly rear window, plus they are a bolt in option only and not made to be easily removed

I liked how the hard top on my NB could be fitted, and removed, by myself, in less than 5 minutes

I know it sounds bad, but I'm waiting for someone to write off a car with one so I can swoop in on their pain, it will go to a good home though, so my guilt of this is tempered

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...