Jump to content
SAU Community

Recommended Posts

Good morning all,

I've been doing some maintenance on my r33 and reckon I can make a convention cross flow intercooler fit custom return piping, utilising half my existing return flow piping.

Has anyone used Mishimoto intercoolers before there particularly the m-line or s-line and how this compares to say a Hdi.

Worth noting used in P98 setup hi teens boost 250-300kw range.

https://www.mishimoto.com.au/mishimoto-universal-intercooler-large.html?utm_source=facebookAU&utm_campaign=DPA&gclid=EAIaIQobChMIz8rdjISF6QIVTyUrCh2U0QHYEAQYASABEgINb_D_BwE

https://www.mishimoto.com.au/mishimoto-universal-front-mount-intercooler-s-line.html

I've used an Mishimoto 600x300x65 mm years ago on my R33 GTR it wasn't any better then the stock cooler. That was later upgraded to a 600x300x100mm which worked ok, car made 410awkws. Pretty much as what you would expect from an cheap ebay cooler, and it was only half the price back then.  

Edited by hypergear
  • Like 1

Plan was to use something like this feeding the hotside to the top left. 

https://www.ebay.com.au/itm/293552927719

I know 180deg bends aren't ideal but surely one bending over 300mm (my current return flow intercooler is 300mm high and hotside runs underneath without clearance issues)

Is better flowing than the sharp turn standard returns flows run.

 

1 hour ago, Dose Pipe Sutututu said:

If you're after a cheap intercooler that is somewhat decent for the price point, those HDi GT2 cores aren't bad, just that link you sent is of a CT2? 

Haha I was like "what's a CT2 as well"

I think he meant to write GT2 as the stamp on the intercooler on top in one of the pics.

1 hour ago, WR33KD said:

I’m running a cheap cooler and it’s doing it’s job for over 400kw. Think it set me back $200. 

On e85? Cooler matters a bit more for 98

Edited by Pattey21
51 minutes ago, Pattey21 said:

Cooler matters a bit more for 98

Coolers matter much more than a bit on 98.

Old setup I was making 372kW at the rear treads on a Mainline dyno w/ 1.7bar of boost going through a dim sum bokchoy eBay special FMIC with intake temps of 65+ degrees Celsius however that was on E85.

Would be knock city on 98RON with those intake temperatures.

Intake temps on a hot summers day get up around 50 and that’s on 98 going for a retune in the next couple weeks going to push for 500kw on pump. 
intake temps are always low with mine has great flow and even the water doesn’t go much passed 95 on the track 

16 minutes ago, WR33KD said:

Intake temps on a hot summers day get up around 50 and that’s on 98 going for a retune in the next couple weeks going to push for 500kw on pump. 
intake temps are always low with mine has great flow and even the water doesn’t go much passed 95 on the track 

...and you live in New Zealand don't you ? Define a hot summers day. Ambient temps are quite a lot lower there on average.

? Very lucky, you have quite ideal forced induction weather over there. I consider 30deg C quite a cool, moderate day where I am. Even places like Melbourne and Adelaide go well past 40 C these days in summer.

So by the way where are you located Pattey21 ?

6 hours ago, BK said:

? Very lucky, you have quite ideal forced induction weather over there. I consider 30deg C quite a cool, moderate day where I am. Even places like Melbourne and Adelaide go well past 40 C these days in summer.

So by the way where are you located Pattey21 ?

In the ACT. Pretty unfriendly with imports with regards to inspections

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...