Jump to content
SAU Community

Recommended Posts

Hy guys

I drive an R34 GTT actual i use Castrol 10w60. I hear its better to drive with 10w40 like motuls turbolight. I have no oilcooler installed engine is stock with nistune 340ps. Who drives 10w40 from motul with no oilcooler and how good is it, like oil pressure stability oil temp etc.

Thanks  greets from Switzerland

20200321_172928(0).jpg

Link to comment
https://www.sau.com.au/forums/topic/480262-a-swiss-dudes-question/
Share on other sites

I drive the car only in spring or summer never at winter. I drive normali in the city or on landroads and  mountain and  at this point i push it really hard.

With the 10w60 i got in the summer over 100 degres.

I think the piston rings are good  compressiontest is between 11 and 12 bar. 

Oilpressure with the 10w60 at 90 degres is 2.2 bar at idle speed 1000rpm

So that sems to be ok too.

 

With the castrol 10w60 supercar the temp gets under full load and  hard drive up to 110 degres. How it looks with the 10w40 i read that the motul turbolight is good for the rb engines. But only for normal drive? And whats with the hths in the oil? 10w60 is 5.8mPa and the 10w40 only on 3.7mPa so is that good? I asked this question because i have  a stock engine but 340hp with the nistune and run 0.9 bar if that helps.

honestly mate, the car is making pretty basic power levels and you aren't racing it. Modern synthetic (or even semi-synth) oils are excellent compared to the olden days for everything up to short sprint/race use. So chuck in any 10w40 or 5w40 synth you are happy with and save a fortune.

Re temps, personally I'd be looking to keep it under 100, 110 and higher isn't a disaster but it does get hard on everything. Since you say you only drive in summer just add a medium sized oil cooler in good airflow and you should never have to think about it again. Plus, adding an oil cooler is cheaper than putting race oil in every 5000klm

  • Like 1

Only if your cooler sucks.

A good oil cooler drops temps massively. I run the Trust coolers with 70deg C thermostats, so they don't pass below 70. The 32 has a 13 row and the 33 a 10 row.

Castrol edge 10w60 is good stuff. I use it on 2 of the GTRs, but we also have 45deg C summers. On the big HP RB26s or heavily competition the weights favoured by the big workshops seem to be the 10w60 or 15w50 depending on climate and/or bearing clearances.

With your power level and being a street only car the 10w60 is probably overkill, but it won't hurt it. 10w40 is the generally accepted standard weight for an RB26.

Unless you know what the temperature actually is (with a sensor) then you don't really know.

A 10-60 is thicker than a 10-40 at 100C. So it won't change the temp, but it will change the viscosity, so if you're targeting a specific viscosity it could sort of matter.

Yes absolutely, which is more of a big end and mains bearing clearance issue regarding viscosity when an engine is really being pushed. Large clearances will require a thicker oil, small clearances lighter oil.

We are talking about a mostly standard engine here so a 10w40 will be more than adequate cooler or no cooler. If he drops in 10w60 still won't hurt it, oil pressure will definitely be more which ain't a bad thing - cooler or no cooler.

  • Like 1

My only fear is that if the engine is REALLY being pushed, as in 130-150+C oil temps, it may be better off having 10-60 in there than 10-40.

There is sorta some logic in going with a thicker oil if you do know it's gonna get hot. That said, there's not a lot of in between where someone will take that as an option before they actually get an oil cooler and get oil temps under control. You should find that with enough cooling it'll be hard to really get up into the 130-150C range anymore, and thus the oil choice tends to be 10-40 or 50 if you really want to go ham/rebuilt engine with more clearances.

Realistically though, still don't think there's been a engine failure on this forum that someone can actually claim was bad oil/wrong oil, at least not in the realm of "10-40 or 10-60"?

 

I think it is important for people to realise something. The difference in viscosity between a 40 oil and a 60 oil, at the temperatures we're talking about (100+°C) is precious bloody little. At 100°C a 60 grade engine oil is sitting at ~20 cSt. The 40 is at about 15 cSt. The gap narrows as they get hotter. At 120+°C there'd only be a couple of cSt in it.

Table_5_viscosity_comparison_chart.jpg

Take a look at the right hand end of this chart to see how all these oil grades collapse towards the same viscosity at the higher temperatures.

graph_4_viscosity_comparison.jpg

 

All this does is tell you that it is VITALLY important to control oil temperature. Selecting a 60 over a 40 is not the correct solution. It's not even a good idea, as it will lead to a placebo effect making you think you're better protected, when, really, not so much.

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...