Jump to content
SAU Community

ADR approves bonnet/hood

Clk195_R33
 Share

Recommended Posts

GTSBoy Grand Master

GTSBoy

Posted
Posted

There is no such thing, other than the original bonnet.

If you want a carbon fibre bonnet legal, then you would have to get a consulting automotive engineer to sign off on it. That is a very unlikely thing to happen, as the problem with CF bonnets is their crash behaviour is totally different to the crash behaviour of the original (steel or ally) bonnet, and in fact much much worse in that they are really stiff and also tend to fracture with sharp edges instead of crumple. So, unless you go and do some crash testing I would like to suggest that no engineer is going to put his nuts on the line and approve a CF bonnet.

Clk195_R33 Rookie

Clk195_R33

Posted
  • Author
Posted

I appreciate your input GTSboy. But I’m well aware another company (blits body kits) make an ADR approved bonnet. 
 

pretty much looking for someone that’s had one and the paper work to prove it. 
 

 

mlr what did you do and how did you go about certification? Also what paperwork did you get? If there was any paperwork to prove it’s been signed off 

The Bogan Grand Master

The Bogan

Posted
Posted
1 hour ago, Clk195_R33 said:

I appreciate your input GTSboy. But I’m well aware another company (blits body kits) make an ADR approved bonnet. 
 

pretty much looking for someone that’s had one and the paper work to prove it. 
 

 

mlr what did you do and how did you go about certification? Also what paperwork did you get? If there was any paperwork to prove it’s been signed off 

There was some docs from Blitz, plus some tag/decal under the bonnet IIRC.

I was sceptical until the engineer and the RTA said they were happy.

This was a few years ago now, I would speak to your engineer first, and see what the RTA says about panel modifications now.

I did have flush bonnet pins installed as well, maybe that had something to do with it, maybe????

Clk195_R33 Rookie

Clk195_R33

Posted
  • Author
Posted
On 27/08/2020 at 6:49 PM, mlr said:

http://www.blitsbodykits.com.au/

I had a FRP on my 33, engineer was happy to sign off on it, RTA was happy with it as well.

 

Was heavier than OEM but worked great for cooling.

drags 24 oct 12.jpg

Would there be anyway possible to dig up the ADR certificate/email? Or anything ? Haha

The Bogan Grand Master

The Bogan

Posted
Posted
56 minutes ago, Clk195_R33 said:

Would there be anyway possible to dig up the ADR certificate/email? Or anything ? Haha

The docs went with the car about 10 years ago, it has changed hands several times since I had it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...