Jump to content
SAU Community

Recommended Posts

8 minutes ago, GTSBoy said:

So, capable of more flow. If needed. Which usually is not the case.

Don't worry, I'm with you, I said it earlier. Issues are usually airflow and oil cooling. 

  • Like 1
  • 3 months later...

Its been a while, but after 4 months, my GrA Reimax waterpump has been installed. I also replaced the GKTech fan with a new OEM R32 Fan. Everything else is the way it was prior.

The reason I went all out was to try fix my annoying(picky) ECT creeping up at idle. It def ran cooler. I noticed that the temps would come down ALOT quicker. Cruising temps on the motorway is around 72-74 for ECT, same as my oil. I have seen the temps down to 67 in the arvo a few times while driving too(its summer time here too).

Has the waterpump made a difference? Yes I think so. 

The other day, I took it for a drive on a HOT day(27-28). Felt so much hotter, plus I purposely drove through lots of traffic. Max ECT was 82.

My ECT temps at idle we ALOT more stable. Prior, it would creep from say 78 through to 82~ in say under 2 mins, and my 2200CFM AC Fan would come on at 85 which would struggle to bring it back down.

Now, the fan doesnt come on. Mind you, I now run a sequential box, and have heat wrapped my downpipe soo..I had a habit of coasting it in neutral everytime(Never used engine braking), but now I have to stay in gear and engine brake all the time which will aid in temps as there's no spark when you decel in gear.

Would it have made the same difference without the box and the heat wrapping? I think it would have. It was my idle temps that was the issue for me, and that seems to be much better(Might be too early to say its fixed).

  • Like 1
20 hours ago, joshuaho96 said:

I wouldn't be all that concerned about coolant temps until 90C but sounds like it worked out for you.

As I said, I was never worried about how high my ECT peaked.. but moreso how fast it creeped. Need to do more testing to conclusively say its a closed book.

On 25/01/2023 at 9:26 AM, Predator1 said:

I also replaced the GKTech fan with a new OEM R32 Fan.

I feel this is what made the difference, however my thoughts are subjective and not based on any data on Skylines.

(Did have 3x S15s with overheating issues at the track, told all 3x to put back the OEM fan blade and... Yep no more overheating).

  • Like 2

Yes, I have also heard the gktech fans are not the best. I have just splurged on an FPG unit, so hopefully that works out well..

The only other thing I can think of would be to go to an electric water pump, which would give you full control of flow at any vehicle speed. I see that PRP have a new RB electric pump that has been released. This is the way I would go when my pump needs replacing..

  • Like 1
On 25/01/2023 at 9:11 AM, joshuaho96 said:

I wouldn't be all that concerned about coolant temps until 90C but sounds like it worked out for you.

90c? 

When racing heavy loaded circuit, I wouldn't lift off until I got to 112 degrees. This was with 600awhp. 

I would ease off at 112c, and it would start dropping back almost immediately. 

90c is nothing. Lots of modern engines run at 100 degrees as standard. 

all the way up to 110 degrees is okay, just start watching it above that. 113c is my hard limit. 

28 minutes ago, The Mafia said:

90c? 

When racing heavy loaded circuit, I wouldn't lift off until I got to 112 degrees. This was with 600awhp. 

I would ease off at 112c, and it would start dropping back almost immediately. 

90c is nothing. Lots of modern engines run at 100 degrees as standard. 

all the way up to 110 degrees is okay, just start watching it above that. 113c is my hard limit. 

Jono living on the edge haha...

I play it a tiny bit safer, just trim the limiter to tell me the car is getting warm. Ain't nobody got time for gauges when you're racing.

image.thumb.png.3c96a52b934add81af6ef65d8220bc2c.png

10 minutes ago, Dose Pipe Sutututu said:

Jono living on the edge haha...

I play it a tiny bit safer, just trim the limiter to tell me the car is getting warm. Ain't nobody got time for gauges when you're racing.

image.thumb.png.3c96a52b934add81af6ef65d8220bc2c.png

haha mate, I definitely don't have time for gauges. 

I get a very big red full screen on my dash alerting me when I'm at 112 degrees, it's a bit hard to miss. 

At 113c, it starts to pull the limiter down. 

  • Like 1
  • 11 months later...
  • 3 weeks later...
On 13/01/2024 at 3:57 PM, SiR_RB said:

So these pumps have been out for sale now for some years

 

has anyone here used one and whats the comparison to an oem or even n1 unit ?

I posted one a few replies up. Before I parked her up, I did lots of highway pulls. I def noticed that the ECT was alot more stable. Did lots pulls in high gears to redline and I was def happy. Safe to say my ECT issues were completely fixed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...