Jump to content
SAU Community

Recommended Posts

On all on my windows the guides are beginning to scratch the window. Apparently there is a foam guide which wears off over time and then begins scratching the window, its either plastic or metal, while the window moves up and down. Apparently this the case on most R32's and on the GTR's when this occurs it scratches the window in two places.

This is supposed to be a fairly common thing on the R32's. Has anyone come across this and know how it can be fixed?

Link to comment
https://www.sau.com.au/forums/topic/71614-scratched-window-r32-worn-guides/
Share on other sites

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Hey Scott,

I've read in the past that the guides can be adjusted in and out. The manual concurs. If there is still a little foam left on the guide, could you adjust it out to relieve pressure? As far as replacing goes, Mr Nissan is prob the only worthwhile plan.

If you suss out a part number, please post it! :( Cause mine are doing the same but now the glass rattles a little and I need some new ones so I can adjust it back, snug against the window.

Mark

mine is same.. light scratches, pretty bad on drivers side. Anybody know how to remove the scratches? How does one polish glass? Heavy duty buffer?

I've looked in there, and I can't see how it would be obviously scratching it. I can kind of see the guides, but don't see how they are putting the marks there. The best solution may be to buy some new foam, and glue it on the points there.

According to FAST there is a part called 'STAB-GLASS' for 2 door cars. I assume this is something like 'stabilsor-glass'. Anyway the PN is:

80324-04U00

but that is superceded by:

80324-04U03, but this has s different decription: BRKT STOPER (Bracket Stopper).

Can't say whether this is the right part. My GTR's drivers side glass also has scratches.

I assume a glazier can do something to fix the glass. There is one quite close to me but I just haven't had time to investigate.

I did a little research and the main methods seem to be a very lightly abrasive polishing (usually for smaller scratches), or some sort of filler that is used to fill the valleys of the scratch (for deeper scratches). The main thing is to get rid of the white colour that glass turns when scratched: at least if its clear the scratch is not so obvious.

LW.

We've used aluminium oxide and a buffing wheel to polish out minor scratches in glass.   It's also what is sometimes used to 'repair' minor scratches in windscreens.   It's a very slow process.

My scratches are probably beyond just buffing. I will try and call the local glazier tomorrow and see what the can do. Will report back with details when I get them.

LW.

I used to work with glass.

If you can grab the scratch with your nail there's no hope in fixing it.

If its simply light surface scratches then it can be buffed out fairly easily, (5-10minutes) with the right polisher.

Basically a big arsed angle grinder looking thing with a huge white polishing wheel on the end. :)

I had never used it but if you weren't carefull to continually move the polishing wheel it would put an indent in to the glass, which looks crappy and suprisingly stands out quite a bit.

I can't remember what it was called but it was a brown powder that was mixed with water and then buffed with a polishing wheel.

On the note of adjusting the windows has any one done it?

My drivers side window appears to be pointing in towards the car a little and has caused the drivers rubber to rip in the corner. :)

It was fine before the car was sprayed. They must have adjusted it incorrectly.

I have had a quick look, adjusting the closed height is easy but the horizontal movement I couldn't work out.

Mine has done the same, only the drivers side. Rubber is ripped and the window is closing way to far in. It needs to be out another half centremeter or so.

There are four nuts and screws, 2 at the top, two at the bottom. Back off the nuts so you can adjust the screws and this moves the regulator holding the glass.

Its pretty precise though, I ****ed it up, need another go :(

  • 1 month later...

Add me to the list, got it on all FOUR windows, white strips about an inch wide of light scratches. I have 4 replacement pieces of glass but haven't put them in until a) I find out how to stop it happening again. B)I get them from my parents in Melb. c) I can be arsed.

I've been told that windscreen companies can clamp some sort of polisher onto the windows.

Also, be really careful if you're replacing the pads. The little plastic clips get fragile with age.

If anyone prices the pads or the clips, let me know. I've got the same problem ;)

There could be a real market for a group buy of pads by the sound of it. At least it will stop the scratches getting worse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...