Jump to content
SAU Community

Recommended Posts

Just out of interest (for S2 AWD models) has anyone tried El Grand front rotors?

From the measurements I've found for the TE 52 these should in theory work?

290mm Diameter
28mm Thickness
49.2mm
68mm centre

  • 1 month later...

Ok all I have no pedal. I have a s1 just swapped the fronts for 32gtr. I used the stock stagea line and banjo bolt. I can bleed them no air is coming out but when the car is running there is no pedal at all unless u pump it up but wont hold it after. I have a hissing sound when u pump the pedal and the car will rev hunt. What could be the problem

Did you remove the restrictor in the banjo hole?

Perhaps the master cylinder is leaking inside the booster? Only because the revs hunt on application... Or the booster diaphragm might be leaking.

Nar dont see any leaks at all. Not dropping the fluid level and no fluid dropping from the calipers

It sounds like the master is your culprit in this situation mate. You may want to check the seals on the master before going any further.

If you don't clamp the lines before undoing the banjo from the stock callipers, there is a good chance you will get air in the ABS motor and these sort of issues will arise. I have bled the ABS lines myself, it just takes a lot longer as the air doesn't like going down hill.

  • 1 month later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...