Jump to content
SAU Community

Recommended Posts

Top Secret sell bonnet dampers... Check out those prices  ;)

http://www.topsecretjpn.com/bonnetdamper.shtml

I've seen bonnet dampers on Skylines Downunder before. There was a big thread on it.

Roy, if you do decide to go ahead with this, I will be interested. See, for me, it's not so much laziness to use the bonnet holder stick. Whenever working on the car, everynow and then I might bump into the stick. I keep thinking to myself, one day, the bonnet is going to fall and chop my arms off, or break my neck. It's more for the convenience of the bonnet just staying.

They were much cheaper on Skylinesdoownunder because they were made by a non gucci jap company. I think they were somewher around $200.

Like i said, if you guys go ahead with this, i'm interested.

I don't see why you'd pay that much.

Why not just get some generic ones from a wrecker? and use those.

Surely they can't be too much different than ones that would keep other non-automotive related stuff open and be much cheaper.

The thing i'm looking for is one that is straight bolt on. That is, no holes drilled etc. Coz the area where the strut is located on the r33 is very very tight, and would be difficult to retrofit one myself. That's why I'd prefer to pay $200 for something that bolts straight onto the stock bracket.

The ones on the boot wouldnt have enough throw or pressure to lift anything the length of the bonnet, although I think the idea of having one each side to equalize the forces would have to be better on the hinges than having just the one strut.

I've done this for a Golf 2. Not a hassle at all. The best place to get the shocks from is froma Honda's boot (sedan type) use one on each end and you can but the ball hinges from repco or supercheap if I remember correctly. Cost one hell of alot less.

I've seen a line done with longer ones off of a hatches bootlid, a little trickier but doable to.

these were all the rage at the Tein stand at Tokyo Autosalon this year. i didn't really see what all the fuss was about but having tein dampers hold up your bonnet certainly is a nice wank.

The real worry Troy is how often your bonnet must need to be open that you are thinking about this!

They do lose their lift after a while, so you'd be looking at replacing 'em every few years or so depending on how long they last.

My sister bought a Citroen Xsara that has a gas-strut for the bonnet an it stopped working after 2 years. In Citroens wisdom they never added a manual bonnet stay, so if you need to check the engine you need someone to keep the bonnet up for you!

Roy's been checking out cefiros that's why he wants them :P

POOMBAH - That's Xsaras for you. My cefiro's struts are original from what I can see and they hold the bonnet up unless it's windy, on a slope or I hang a lamp from it (they're just on their way out). 16 years oh yeah Nissan.

They do lose their lift after a while, so you'd be looking at replacing 'em every few years or so depending on how long they last.

My sister bought a Citroen Xsara that has a gas-strut for the bonnet an it stopped working after 2 years. In Citroens wisdom they never added a manual bonnet stay, so if you need to check the engine you need someone to keep the bonnet up for you!

sounds like quite a shit car. my soarer has them and it's bonnet is huge and bloody heavy and they work fine. Car is just over 10 years old.

hehe yeah, that's women for ya, they buy cars more on looks most of the time.

Yeah the Xsara is only 3 years old and has so many problems.

I always give her a good ribbing about how my 11 year old japanese car still runs a treat.

Frankly, my beat up old '89 seca runs better hahah

hmmm.. might take the 'ol corolla for a spin rite now...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...