Jump to content
SAU Community

Recommended Posts

  • Replies 714
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

well ive sent 3 pms to him over a month ago and still no reply, not even a confirmation... thats all i want

pm.s should be as good as an email,as he doesn't have to read this specific thread

will try an email for the fun of it

Does anyone have a phone number for Jamex ?

i have tried 2 different numbers and i cant seem to get the right company, one is in VIC and is an electronics company and the other is something in menai marketplace

also is jamex at 43 yanderra ave bangor?

  • 3 weeks later...

just an update, all parts delivered personally

installed swaybars and subframe mount bushes and f**k what a difference.... very good and recommended

Hi All

Matt here

To Anyone who could not get through, I am now answering PMs and all questions for Gary the best I can. With the new business extremely busy, we have been flat out, however gary is off on Holidays to the USA next week for 5 weeks. This does not mean that sales will hault, as I will personally be looking after all sales and enquiries from this point on. For anyone with more technical questions, there are some I can assist with, but any that I can not will be forwarded to Gary.

So please, PM me (I will check the GB threads when possible, but PM is best - I will supply an email address and a phone number for me)

Cheers

Matt

so the settings on the first page are just for a road kit right? what about the track settings?

also, which parts are suitable to compliment existing coilovers?

so the settings on the first page are just for a road kit right? what about the track settings?

also, which parts are suitable to compliment existing coilovers?

As per previous post...PM me man!!

I'll answer anything.

Track settings - Need details on the car, what's in it, what you wanna do

Again - what do you have? What do you want from the car? Budget?

PM me, I'll give you my email

  • 3 weeks later...
  • 3 weeks later...

Thanks Matt/Gary,

I know I ordered at a bad time, so I had to wait. I got my shocks, bump stops and covers. Measured it today before fitment and got 335mm front, 340mm rear. I will raise the front one groove. Should make it handle better, more comfortably and give me some more gutter clearance. We'll see how it goes in practise.

I had no idea it was THAT low....guard is still about 5mm above the tread.

Thinking about it I assume that raising with short springs gives a limit to the suspension and could cause "topping out", if you know what I mean- when the other wheels compress.

Edited by simpletool

Put in the front shocks, and raised by one notch (now on 2nd top notch). Car sits about 1cm above before, is much firmer when braking and turning while also being very much more comfortable over sharp bumps. Overall feels firmer, but you don't have to whince when a road join comes along.

Overall it did what it says in the thread. Happy.

Yet to put in rear shocks.

btw 345mm at the front seems really good, springs must be some Jap spec ones that came on the front of the car.

  • 2 weeks later...

i've had the shocks, springs and camber kits in for a couple of days now. has made a huge difference. however i did notice that while it soaks up the smaller and sharper bumps, the larger ones set me bouncing a lot, esp if there are more than a couple in a row. oh and also if there are ripples/bumps etc in a corner it tends to bounce my back end out. is this normal? i've never had am suspension in any car i've driven and i dont think its a setup prob cause it was installed by centerline in vic

  • 2 weeks later...
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Some of the filler.   Also if I look under the top flap of metal it starts looking good quite close to the edge. I get the feeling it doesn't go much further.
    • So, I finally started digging at the bit of my roof that was cracking and bulging a bit. Well, it was just thick filler that was covering some pretty bad rust. I didn't find the edges, I was too bummed to keep going.  There are a few holes as you can see. There was just so much filler but looks like no attempt under the filler to prime or use rust converter, just slapped filler on exposed rust.  Anyway, I'm going to take the windshield out and find the edges. I'd love to fix this myself as I'm pretty sure it'll be expensive to get done properly. I was thinking I could just get a cut piece from another E39 and just weld it in place as it would be the right size and shape.  Thoughts?
    • This is the territory of the "Stage 1/2/3 Golf GTI/R" or otherwise off the shelf tune with (relative to before) minor mods. It's easier now. Downpipe and Tune and boom, big increases. Stage 1 OEM+ is where it's at. This is where the niche evolved into and it's really easy to see why. It's rare to even NEED to consider changing turbos or going to aftermarket ECU's or building bottom ends for more power. Stage 1-2-3 will get you a LONG WAY. Civic Type R turbo GR Yaris/Corolla Anything with B58 (MKV Supra/x40i) Anything BMW in General Anything Audi in General Any turbo AMG RenaultSport Turbo offerings Korean Elantra N/I30N Ecoboost Mustangs Focus RS? List goes on. I would argue in the future it won't even need to go on... M3P is pretty rapid out of the box...
    • There is a way, but it's not with the same cars. You need to find the same vintage of car, that we had. Realistically, that was an affordable car with aftermarket parts around. So what people need to find is a car that had a decent base in its day, and can be modified. They're looking for a car year make of 2010 to 2015 really... Aus could have done it if Holden didn't fold as V8 commodores were cheap, and if Ford didn't get expensive thanks to COVID, then you could cheaply play with FG Barras. Realistically, those are just a bit heavier, four door skylines. I'm sure the US and UK have similar cars they could find.
    • Haha I do that.. thats when it chirps..The bit point for me is almost non-existent. Otherwise I stall it. But yes, in terms of performance, the clutch is solid af.
×
×
  • Create New...