Jump to content
SAU Community

Recommended Posts

If anyones wondering what 18" white Advanti Samurai's look like here you go. They are 18x9 +35 and 235/40R18 tyres. Minor stretch. I dont really like stretch but it was necessary as you will see when you scroll down. The bottom of the coil over adjuster nuts were rubbing on the rear tyres. Fortunately I just needed to raise the coilovers about 10mm. Its still pretty low though. If they had +30 offset I wouldve got that but anymore poke is just ricey IMO. Running 18x10 with 20 offset is not for me! haha. For the record this rim/offset is fine with TEIN coilovers set to a reasonable height.

For you guys still confused (and fair enough), this site helped me heaps, and kinda renders this thread useless, if it werent for the sweet stagea pics lol.

http://www.willtheyfit.com/index.php?width=215&aspect=45&diameter=17&wheelwidth=7&offset=45&width2=235&aspect2=40&diameter2=18&wheelwidth2=9&offset2=35#content

Just find out your current width and offset (should be on the rim, inside), check the clearance on the inside (suspension) and outside (guards) of your current wheel, and enter the specs of your new wheel.

Ilrv3Ey.jpg

1QmyeH8.jpg

N61Biui.jpg

You can see if I went with 255's it wouldnt have fitted.

tkdDhmD.jpg

  • 1 month later...

Righto, I've been looking and reading and looking and calculating some more and I've settled on 18x9.5 +15 with 265/35s all round on an S2 C34 RS4S.

It's running Bilsteins and it's got a fair bit of low installed but by my calcs they'll fit properly, without having to resort to crap camber to make them clear the struts.

Can anyone spot anything I might be missing?

You are legendary. Going by those pics they'll fit, although the clearance between the inner tyre and strut will be a bee's dick. Worst case I have some 5mm spacers to give a tad more clearance. Not ideal, but the car is just a cruiser so no biggie.

Cowboy1600, here's some more detailed pics, also a S2 C34 RS4S with 18x9.5 +15 but with 235/40's. Center of rim to the guard is about 340~345mm.

20150927_072223%20%281024x576%29.jpg

20150927_072250%20%28576x1024%29.jpg

20150927_072323%20%28576x1024%29.jpg

20150927_072431%20%28576x1024%29.jpg

What happens when you throw it into a corner? You can get the same fitment and the same rubber on the road with 18 x 8in and 235 tyres:

2014-02-02181113_zps8e8a8198.jpg

2014-02-02181000_zpsf6f87731.jpg

It's not the fitment I'm concerned about, more the rubber. It's at 230rwkw now and the 235s on it now struggle. Once I decide on a new intercooler and get it back to Trent for a tune it should be north of 300 and 235s will not stand a chance.

I've converted to RWD so need 265s to tame the rear.

It's not the fitment I'm concerned about, more the rubber. It's at 230rwkw now and the 235s on it now struggle. Once I decide on a new intercooler and get it back to Trent for a tune it should be north of 300 and 235s will not stand a chance.

I've converted to RWD so need 265s to tame the rear.

Sure - my comments were more directed at Jase with his big wheels and small tyres.

You just need to get your wheels away from the suspension and then take to the guards with a big hammer!

I know my set up is far from ideal, i will admit that. When i bought the stagea it had 18x8 with 235/40 tyres and 18x9 265/35 tyres with 20mm spacers front and rear. I dislike spacers and i was having issues with the 4wd because of the mismatched tyres.
The cst's popped up at a price i couldn't refuse and made them fit.

It handles just fine, i cant notice the difference the two set of rims it had.

  • 2 weeks later...

OK, ended up with 18x8.5 +15 fronts with 235 40s and 18x9.5 +32 on the rear running 265 35s.

Fit is perfect. I had them roll the guards while I was there for a bit of extra room. It is rubbing somewhere but I I'm not sure where yet.

It's looks perfect!

gallery_69546_5900_657883.jpg

OK, ended up with 18x8.5 +15 fronts with 235 40s and 18x9.5 +32 on the rear running 265 35s.

Fit is perfect. I had them roll the guards while I was there for a bit of extra room. It is rubbing somewhere but I I'm not sure where yet.

It's looks perfect!

gallery_69546_5900_657883.jpg

What are they?

Black always looks great against the yellow.

  • 1 month later...

Will a set of 18x9 +35 fit an s2 stagea rs four s?

Nope.

I've run into a problem with mine (18x9.5 +32)

They hit the strut on the inner lip going over bumps. I'mm going to run 10mm slip on hub centric spacers with longer wheel studs to get around the issue.

For 9.5s you want minimum of +22 i've decided, based on my experience. So 9s give you about 6mm extra clearance,, so you'd want max of ~+28 offset.

Nope.

I've run into a problem with mine (18x9.5 +32)

They hit the strut on the inner lip going over bumps. I'mm going to run 10mm slip on hub centric spacers with longer wheel studs to get around the issue.

For 9.5s you want minimum of +22 i've decided, based on my experience. So 9s give you about 6mm extra clearance,, so you'd want max of ~+28 offset.

Thanks! Now am looking at a set of Varrstoens, same 9.5 width, and come in 12 and 22 offsets. Any ideas which would be best? thinking 12 on front and 22 on rear?

Thanks! Now am looking at a set of Varrstoens, same 9.5 width, and come in 12 and 22 offsets. Any ideas which would be best? thinking 12 on front and 22 on rear?

9.5+12 will stick out a mile on the front, where a 9.5+22 will fit under with a 245 wide tyre with some minor guard rolling.

A 9.5+12 would probably be just about spot on for the rear; might still want the lips rolled lightly. Even the +22 looks bloody good, and having all four the same offset means you can rotate wheels easily.

  • Like 1

9.5+12 will stick out a mile on the front, where a 9.5+22 will fit under with a 245 wide tyre with some minor guard rolling.

A 9.5+12 would probably be just about spot on for the rear; might still want the lips rolled lightly. Even the +22 looks bloody good, and having all four the same offset means you can rotate wheels easily.

I've got 18x8.5 +19 on the front with 245s and they fit beautifully. We test fitted 9.5 +15s on the rear and they stuck out too far. +22s are spot on for the rear IMO (On a C34 rs4s). Will need guards rolled if the car has a decent amount of low installed though.

Will a set of 18x9 +35 fit an s2 stagea rs four s?

definetely not.

i got r33 gtr wheels (I know its 17x9 +30 but extra inch in the wheel would make mine much worse) on mine but the rears scrapped massively, got 15mm bolt on spacers but still scraps over bumps. I would need atleast another 5mm to clear struts over bumps. mine is lowered so if its higher or has adjustable camber arms could probably get them further away from the struts.

as for the fronts i have plenty of room no issues with the +30 but i would again go further down towards a +20-25 atleast.

Okay. just found out that my shop can get rotiforms in, and for wicked employee deals, so I am going to get a custom set of these made up. Going to stick with 8.5 wide to make choosing an offset a little more forgiving. I seen earlier in the thread someone said s2 rs4s should be good with +6 all around. Thoughts? Not opposed to guard rolling at all, would just like to be able to do without spacers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...