Jump to content
SAU Community

Dose Pipe Sutututu

Members
  • Posts

    15,517
  • Joined

  • Last visited

  • Days Won

    371
  • Feedback

    100%

Everything posted by Dose Pipe Sutututu

  1. weird looking A90 Supra haha
  2. Get extenders and then punch a small hole through the parcel tray 😎
  3. House is coming along nicely, manufacture that equity baby!
  4. Old school fuel caps do I fact seal the fuel filler neck, however there's a vent elsewhere. As of the 80s ish fuel caps started to incorporate 1x way valves to allow air in as Duncan has described.
  5. Been waiting a while for 3rd gear skids.
  6. Hopefully the OG layout is still there, would be nice to see what the shit box can do now with further development.
  7. please post up skids
  8. Something like this: https://www.ebay.com.au/itm/373980625436 Has 0.2bar opening pressure. Fuel tank -> Check Valve -> VTA
  9. put a small valve there, something that cracks after 0.1bar of pressure, if not you'll always smell fuel as the fuel tank breathes. I have a one way valve, that cracks open at 0.1bar, some eBay junk. Stops the smell in the garage.
  10. One can make an educated guess and say both are the same, because when you go to order a Tomei or Nitto RB25DET NEO head gasket, it's the same for the non-NEO motor. NEO head gasket has higher revision number and is cheaper, sounds like a winner to me.
  11. Don't the G D R fellas use JB Weld to repair their cracked blocks? Lol Also with the insatiable demand for RBs (thanks to the muricannnns) there would be a future where sleeving these blown blocks and repairing them is the norm. If you have space, maybe keep it?
  12. Last time @admS15 used his launch control, he lost a turbine LOL.
  13. Loaded up the latest firmware, oh wow... went for a drive and it's like I've setup Alpha-N and MAP compensation. I thought the transient table I built was good, but wow... this just brought it to another level. @R3N3 this is how I make the car brap lol.. sounds better than rotational idle Nice little timing hole lol And for the idle control you want it to not much between -50 ~ -100 RPM
  14. Washed the shit box, forth wash since the start of 2021 when the respray was done.
  15. Doesn't the article say this though? It's estimated the track contributed almost $17 million annually to the Goulburn economy $17m to a tiny town is quite a bit of money for the economy.
  16. DCT conversion, dry sump, stroker, twin scroll modern turbo setup, surge tank, etc. Skyline ownership dis dat.
  17. I don't think you can easily, unless you get creative and set up a Generic output condition to override it. I just have mine turn from 50°C onwards, car struggles to idle with it on when it's cold lol.
  18. If you want good brap idle, just have VCT enabled from 700rpm onwards and lower the idle timing in your zero demand table. I have it bouncing between 20 and 8 degrees LOL. In terms of launch, I really haven't dialled it in as I just use the rolling anti lag switch for launch. That blankets retards 18° of timing and with ignition and fuel cut 100rpm over target. Gives me a little over 1bar of boost at 4500rpm or about 1.3bar at 5000rpm on a roll. Good for those cruise days at SMSP, and shooting flames lol.
  19. Sensational results, makes me want to swap out my dated GTX3576R Gen 2 for a G35-900. Probably end up spoiling 500 to 700rpm earlier and make much more power and then break other things.
  20. Avoid the Tomei junk, GFB like GTSboy recommended or Turbosmart options are good.
  21. Nice! Looks like it works well, Andy from Haltech must have pushed for that. It allows compensation for when port velocity is so low fuel that is sprayed is turned into a fuel film. I think it's called x-tau in other ECU
  22. Welcome to Skyline ownership, cheaper and more reliable buying a BMW M2 Comp, but here we all are lol.
  23. Car still might work however the fuel pressure is probably all over the shop like you've just discovered.
×
×
  • Create New...