Jump to content
SAU Community

Recommended Posts

Hey guys

R32 GTST

Had to replace radiator.

I think I have an air lock

What is the correct way to bleed the system? I think I should have replaced the thermostat aswell, cause the bottom hose doesnt get hot even after a 40 minute drive (i.e. I don't think it's flowing)

All I have done is run the car till it was warm with the rad cap off. I also tried removing the bleed screw on the top of the engine/inlet. Am I supposed to do that hot or cold? While the car is running? When do I put the bolt back in?

Any other ideas? I assume the bottom hose should get hot? How can I tell if it is passing coolant through or not?

Also, where is the drain bolt on the head that I hear people talk about? I can't find it

cheers

Chris

Edited by eXc
Link to comment
https://www.sau.com.au/forums/topic/102301-bleeding-air-from-coolant/
Share on other sites

have you taken the top and bottom hose off the radiator and stick the hose in the top, then turn it on, to see if it flows?

Huh? Put the bottom hose onto the top of the engine? That would put water the wrong way around?

Can you explain in more detail?

heh... bottom would stay cold if your waterpump died, right?

No flow and no airbubbles when you leave the cap off... would explain that too.

I get air bubbles from the bleed point, and at the radiator cap...well...I did for a while until it put all the air out...

I still get air bubbles at the bleed point....but I don't know the right way to use it.

Water pump is only ~6000 kms old too

Edited by eXc

oh cool.

Black32 means:

1) Take out the radiator completely.

2) Stick the garden hose down the top

3) Watch the water flow out the bottom.

Pain in the ass, but if you really suspect a blocked radiator, this will tell you for sure. (and also give you a nice radiator flush)

oh cool.

Black32 means:

1) Take out the radiator completely.

2) Stick the garden hose down the top

3) Watch the water flow out the bottom.

Pain in the ass, but if you really suspect a blocked radiator, this will tell you for sure. (and also give you a nice radiator flush)

Ok. yeah I did that.

Can anyone tell me how to bleed the system correctly please?

I mean I have been running it for a few days with no dramas so I guess it's all good. But would be nice to check it out.

  • 1 year later...

I need help also!

I have an R32 GTST - RB20DET.

I filled it up with coolant, put the radiator cap back on and started the car.

I then fully removed the bleed bolt. I left it idling for around half an hour with heater on full (32'C FAN SPEED #4). I was told to wait until bubbles stop coming out and you just get coolant but it never happened. Got close a few times, but bubbles kept coming up now and again.

I should note that it wasn't a steady stream of bubbles/coolant coming out. It was very intermittent and sometimes you'd see the bubbles/coolant start coming up but then go back down. A lot of air bubbles came out but still never got just coolant to come out.

Radiator is full and overflow is above min.

What am I doing wrong?

I think you should run the car, then stop it and allow to cool down. open the radiator cap when cool and open the bleed bolt, i just keep adding coolant as it flows out of the bleed bolt until its a solid stream of coolant then put bolt back in and top raditor and put cap back on.

do you guys think my car will be safe to drive???

not much coolant was making its way out of the bleed valve, i would've lost a few mm of depth in radiator after 30mins, thats it.

how long should it take to get all the air out because i had it idling for at least 30mins slowly getting (some of) the air bubbles out but surely it doesn't take that long?

how do i make sure all of the air is out?

I had the same thing. The last time I did it I hardly bothered with the bleed bolt. Just idle it up to operating temp with the bleed bolt almost out and the rad cap open -keep topping up. Take the car for a short drive (with cap and bolt done up). Let it cool..open up bleed screw, then rad cap and add extra.

  • 1 year later...
  • 12 years later...

@cogsDo you happen to know exactly where the bleeder screw is? Having issues getting air out of the system on my rb20 and can't find any info on it. Replaced water pump and thermostat and deleted the heater core inside the car and i can't get the system to bleed properly. Trying to hit an event this weekend. 

  • 3 years later...
53 minutes ago, silviaz said:

I read on YouTube that the neo has 2 bleeder valves? Can't see anything in the manual though

Screenshot2025-01-23at8_48_41PM.thumb.png.7e03e5208b2ad237d7e74aa68cb7c641.png

IACV has an air bleed plug in this part of the engine manual. I'm guessing if it isn't bled it will cause weird idle behavior as the cold start valve won't get hot enough to close properly at the usual rate. 

  • Thanks 1
7 minutes ago, joshuaho96 said:

I'm guessing if it isn't bled it will cause weird idle behavior as the cold start valve won't get hot enough to close properly at the usual rate.

Not that anyone in most of Oz would notice if there wasn't coolant flow.

When I bought my Neo, that whole coolant path was completely blocked with solid crap. I had to dig it out so that I could bleed the cooling system properly, but until I did, I never struggled with idle control. We're not in Idaho.

1 hour ago, GTSBoy said:

Not that anyone in most of Oz would notice if there wasn't coolant flow.

When I bought my Neo, that whole coolant path was completely blocked with solid crap. I had to dig it out so that I could bleed the cooling system properly, but until I did, I never struggled with idle control. We're not in Idaho.

Kind of surprising, with cars this old I've seen a lot of them suffer from high idle due to internal vacuum leak. Fuel trims look fine but the cold start valve just wore out from all the heat cycles and won't close up all the way. Rather notorious issue in some models of the Toyota 4Runner: 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...