Jump to content
SAU Community

Recommended Posts

Good read.

One thing I would like to chuck into the ring is the performance side of things.

I remember when I switched to iridiums in my CBR900. Holy shit. SOP dyno said 5hp right thru the rev range. And it wasn't just the switch from old to new plugs as I had done that 10 times before going iridiums. And throttle response was markedly improved. It help with the throttle hand/rear tyre connection something fierce.

I've been an advocate of iridiums ever since.

Why am I surprised that people don't report better performance with iridiums over copper in their cars?

I picked up some iridiums this week. Will chuck em in with fresh oil next weekend and report back.

  • 3 weeks later...

ok ok very confused after reading all that!

i have brought new coil packs, and i want to change the plugs at the same time and the coils!

my car is r32 with rb25det s2 simple mods fmic, fuel pump, full 3inch exhaust and a hi low boost control 7 and 10psi

i drive mainly on 7psi!

what plugs and what gap?

thanks

ok ok very confused after reading all that!

i have brought new coil packs, and i want to change the plugs at the same time and the coils!

my car is r32 with rb25det s2 simple mods fmic, fuel pump, full 3inch exhaust and a hi low boost control 7 and 10psi

i drive mainly on 7psi!

what plugs and what gap?

thanks

The rule of thump, with those mods you run bcpres6 copper ones and if you boost past 13-14 go 1 colder and get bcpres7

no need for confusion really...

90% of people on here and pretty much every tuner i have spoken to use and reccomned either BCPR7ES gapped @ 0.8 or BCPR6ES gapped @ 0.8

use that and you will be fine

:/

its not that iridiums aren't better also.... its just that in a modified environment they can die just as quickly as coppers and offer no real gains other than the price

Fixed my missfire that i had for 5 months by putting in BCPR6ES at .7 gap, had iridiums in before at at heat range 7 and .7 gap and they were shit, but most likely due to car running really rich for so long.

Put platinum ones in mine about 3 years ago done about 65k still fine checked at each oil change or service

Running light mods and .85 bar boost no problems no miss fire best plugs i've bought so far but a bit expensive

thought id try them after I was surprised they lasted over 160k in my astra 2.2 coupe (holden)

Edited by jjskyline79

I bought a six pack of Bosch Platinums today from Super Cheap. Cost me about $38. They are the FR7DPX ones. Has anyone used these before? They are pre-gapped at 1.1, but keep reading on here folks going for a 0.8 gap. Have read things in this huge thread and will continue to do so. But so far seeing way more references to NGK coppers vs anything Bosch.

yeah, everyone seems to love the nkg's. but when it comes to gapping, if you're pretty stock then 1.1's will prob be ok. it's like oil tho, different for every car, and might take a few changes to get the perfect setup. just listen out for a miss

  • 2 weeks later...

found my cause of misfire, 2 of my coils were missing the spring, and as a result there was some white powder stuff on top of the plug and in the coil at the base.. cleaned out and with new springs and plugs fixed my missfire.

  • 5 weeks later...

was taping up my coilpacks to try to solve a missfire while i save for yellow jackets and had a look at the spark plugs, only to find them very very black. I'm using ngk bkr6es plugs with standard 1.1mm gap and they have about 3500km's on them. do i need a higher heat rating? or is it running rich or something?

car is a stockish r34 gtt with 3.5" catback somehow boosting to 12-13psi (still trying to figure out why that is)

Edited by Galois

If you have dodgy coils try gapping your plugs down to 0.8 til you get new ones. Could possibly explain why they are so black (don't all RBs run rich from stock?) or if you're keen try some NGKBCPR5ES

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...