Jump to content
SAU Community

Recommended Posts

Would it be worth while blowing 2 19" Tyres on the WSID Burnout pad?

We are doing some work to our skyline and have a spair set of 19" Wheels which we thought would be cool to Blow on the Burn Out Pad at WSID on a Wednesday night!!!!

So tell us what you think?

1 - Blow the 19" Wheels and Tyres

2 - Blow Stock Rims and Tyres

We are fitting a mechanical Diff next week, and hopefully the week after we will go till we blow!!!

if you want some 2nd hand 19" rubber go into payless tyres in chullora and ask for jeff. tell him joe with the yellow r33 sent you. ive sold my 19s so i dont need them.

he had 2 sitting at his shop the last time i went, he told me 100-120 for the pair and i think they had 80% tread.

no it wont

you will waste your time and eveyone else's time while you f**k around doing burnouts. just go with normal tyres at a good psi (not 40) and do the best you can do

please do it. just picture how good you'll look when you are dragging your nice cast, chrome rims on the ground, as a big chunk of steel belted radial starts bashing against your rear quarter panel. if that's not going to prove how good you are and how rich you are, nothing will.

Just my opinion. You'll get the same enjoyment out of smoking out a set of 14, 15, 16, 17, 18 or 19" tyres. There is no point to kill the 19s. Just kill the stock 16s.

Regarding the crowd's opinion, do you care what a bunch of mullet ridden, no shoe wearing, buckteethed, singlet wearing, beer bellied, inbred redneck bogans think?

lol regardless of wat sorta skid it pulls those redneck morons will call it shit cause it aint no v8 maateeeeee

No, the fact that there has not been one decient Burnout from a Skyline or any form of turbo car would be the case...

1. You don't win un-less you blow the tyres.

2. Shit Loads of smoke is required.

3. Those Beer Bellied Rednecks in the Crowd is what Judges the Burnout Comp.

4. The Skyline is getting a new rear bar, new side pods, new side skirts, and a Paint Job, so if it scratches the side pannel, I don't really care.

5. The 19" wheels are spare wheels (old wheels we took of the car) I get the tyres for nothing..........

Those Reasons are why I was going to blow the 19" Tyres over Stock...

Oh, I didn't realise you were actually competing. I htought you just wanted a place to blow them legally.

In that case, put the 19s on and smoke em hard. Start in first. Then shift into second. Then third if your car has enough power. That should give heaps of smoke.

Keep smoking them hard. I've seen a video of a car doing a third gear burnout where the rubber got so molten due to the high rpm that when the metallic belt started sparking, the rubber caught on fire. That should get the crowd's attention.

Keep smoking it until the tyre pops, then keep giving it some. Keep them spinning and shred the rims right down.

The crowd should go absolutely wild and you'll win. Doesn't matter about the rims, afterall, they're spare right?

oh, please take camera and make a movie. We wanna see :P

ROFL, thats right, I know how to do a burnout... we will run the skyline to around 15psi, with a mechanical diff center (LSD) 19" Nankangs as they smoke well, and holding it around 6,500 - 7,500rpm in either second or third...

I will prolly start in second as the rears are in the water, dont move for 5 or 10 sec's till its nice and loose, then bang it into 3rd get it to 7,000rpm and have fun!!!!

easy...

we will pull some power steering fluid out as that is what causes most engine fires, but it should do the trick...

But the purpose of this post is:

I have spare ROH Drift R 19" Wheels and Tyres which I will blow in the Burnout Comp

or Stock rims and tyres !!!

19" Wheels would be sweet and live up to my name!!! like always

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...