Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

What is right way to update my engine?

I got 550hp rb26 (r32gtr/circuit) and i bought my car in japan. I dont know manufacturer of oil pump but engine is "overhauled" and got good oil pressure. Is it good idea to put that 1,5mm restrictor and oil drain hose rear of camhead to oil sump. I just bought Trust oil sump and i have to wait 2months to get engine out and weld that sump.. Then i do other tricks same time and check manufacturer of oil pump.

What other tricks i have to do?

  • 4 weeks later...

If you are unclear as what is "recommended" please see the link from Page 2

http://www.skylinesaustralia.com/forums/in...st&id=38818

PDF shows each motor and oil pumps

The length really isn't all that critical. Make it about 7-8mm or something. Width is ~6mm.

I picked up a length of 6mm black rod for the total cost of $2. I wouldn't bother with doing it on a lathe.

6mm black rod, chop, clamp and drill in a drill press then taper one end and use a pin punch to tap it in.

  • 4 weeks later...
sorry probably a stupid question but how much should you drill out the returns? what size?

think of the returns as port matching, if you put a gasket on the deck, you will see the amount of overhang of the rear returns on the block.

take out whats not covered by the gasket

  • 2 weeks later...

May i ask the question with a rb25, why is the front feed blocked off and the rear feed restricted but with the other engines its the rear feed that gets blocked off and the front feed get's the restrictor ??

First attempt at a table;

-------------------- -------------------- RB26 -------------------- -------------------- RB25/20 -------------------- -------------------- -------------------- RB25

-------------------- -------------------- No VVT -------------------- -------------------- No VVT -------------------- -------------------- -------------------- VVT

-------------------- -------------------- Front Feed, Rear Feed -------------------- Front Feed, Rear Feed -------------------- VVT Supply, Front Feed, Rear Feed

Standard Oil Pump

Road ----------------------------------- 1.5 mm, Block off, ------------------------------ 1.5 mm, Block off, ------------------------------ Leave, Block off, 1.5 mm,

Drag ----------------------------------- 1.25 mm, Block off, ------------------------------ 1.5 mm, Block off, ------------------------------ Leave, Block off, 1.5 mm,

Circuit/Drift ------------------------------ 1.25 mm, Block off, ------------------------------ 1.25 mm, Block off, ------------------------------ Leave, Block off, 1.25 mm,

RB26 N1 Oil Pump

Road ----------------------------------- 1.5 mm, Block off, ------------------------------ 1.5 mm, Block off, ------------------------------ Leave, Block off, 1.5 mm,

Drag ----------------------------------- 1.25 mm, Block off, ------------------------------ 1.5 mm, Block off, ------------------------------ Leave, Block off, 1.5 mm,

Circuit/Drift ------------------------------ 1 mm, Block off, ------------------------------ 1 mm, Block off, ------------------------------ Leave, Block off, 1 mm,

Aftermarket Oil Pump (Jun HKS Apexi Trust etc)

Road ----------------------------------- 1.25 mm, Block off, ------------------------------ 1.5 mm, Block off, ------------------------------ Leave, Block off, 1.5 mm,

Drag ----------------------------------- 1 mm, Block off, ------------------------------ 1.25 mm, Block off, ------------------------------ Leave, Block off, 1.25 mm,

Circuit/Drift ------------------------------ 1 mm, Block off, ------------------------------ 1 mm, Block off, ------------------------------ Leave, Block off, 1 mm,

Note that all of the above assumes;

1. Standard Nissan clearances

2. Oil cooler (where necessary)

3. Improved oil control in the sump (where necessary) including wings, baffles, one way doors etc

4. External oil return from cylinder head to sump on all circuit/drift cars and drag cars with non standard oil pumps

5. Hydraulic followers in RB20/25's. if changed to solid followers then use RB26 restrictor as above

6. Castrol Edge 10W60 (or equivalent)\

7. Improved oil flow in the cylinder head return galleries through the block.

8. Refer previous posts in this thread

:rofl: cheers :)

PS; This guide is for what ever cylinder head you use, the block is irrelevant. Whether you use an RB20/23/24/25/26/27/28/30 bottom end is doesn't matter when it comes to restrictor sizes. It's all about what oil pump you use, what cylinder head and what you use the car for.

Edited by SATO GTS

I read the most posts of the topic.. I have an RB25DET and I will make a rebuild theese days...!

The changes I will do is:

N1 oil pump

Block rear feed

1.5mm Tomei Oil Gallery Orifice at Front feed

External oil return

Improve oil flow in the cyllinder head return galleries

But I don't see any post for oil pump collar..!

I need a JUN oil pump crank collar??

Also with external oil return and improved oil flow in the cyllinder head return galleries les is too much oil return??

You are 100% that I will have it any problem at head at low rpms?

I use my car for everyday in traffic, for travelling but and drag,drift,cirquit and I will go for 500hp!!

Getting the oil piump collar is is a 100% must do. especially when using the N1 pump as there has been MANY MANY failures.

I did the oil pump collar on my engine and i still used the standard oil pump which is not prone to cracking and breaking like the N1 pumps are.

so the answer is.. YES. please do the crank collar. if you dont your crazy.

I read the most posts of the topic.. I have an RB25DET and I will make a rebuild theese days...!

The changes I will do is:

N1 oil pump

Block rear feed

1.5mm Tomei Oil Gallery Orifice at Front feed

External oil return

Improve oil flow in the cyllinder head return galleries

But I don't see any post for oil pump collar..!

I need a JUN oil pump crank collar??

Also with external oil return and improved oil flow in the cyllinder head return galleries les is too much oil return??

You are 100% that I will have it any problem at head at low rpms?

I use my car for everyday in traffic, for travelling but and drag,drift,cirquit and I will go for 500hp!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...