Jump to content
SAU Community

Recommended Posts

The 350Z disc cannot be used on the Skyline because of the different hat heights, the 324mm Skyline disc must be used and I understand that the two calipers use different size mounting bolts.

So assuming these are the only differences (to the best of my knowledge) then fitting 350Z calipers would not be an insurmountable task (in conjunction with the GTR33/34 disc) but unless you could pick up the 350 calipers at a bargain price I would suggest using the GTR calipers and saving yourself the hassle

the 350z/ v35 skyline ones use a m14 bolt to mount them where as 33/34 gtr uses a m12.

and ther offset of the skyline ones is off by about 3-4mm.

i tried fitting 33/34 brembos on a v35 and the bolts went big enough and the caliper rubbed on the outer face of the disc :

hope that helps.

ps... you can bolt them up but youd need the matching discs with the calipers.

Thanks guys, thats helpful. I'm interested because a company in the US called RacingBrake has released a 6 pot caliper/adapter/disc/pad set for the 350Z/G35 that's about AUD 2500.

http://www.racingbrake.com/350Z_G35_03_05_...026-311-611.htm

Being the US they don't have access to GTRs like we do so I thought I'd see if anyone knew if they were compatible.

Regards

Edited by Scooby

I think this all got answered, but like t04 said the only difference is the thread on the bolts. Just match calipers to discs and it should be fine. I just never got around to getting bolts the right length

  • 4 years later...

Bit of an old thread bump.

Just want to confirm what I am reading.

If you got a complete front aftermarket brake kit with calipers, rotors and brackets made for the G35/350Z, it would bolt onto a R32/R33 Skyline if you had the brackets have M14 holes on one end for the caliper and M12 holes on the other end to bolt onto the hub correct?

  • 1 year later...

hmmm, interesting.

looking for the same answers for the same reasons...

so, to sumerise, get a complete kit, and it should fit..

is that it?

might have to take the plunge, and try for myself.

if i do, will put up a write up.

Im running r34 brembos on the front of my Stagea which is the same as a v35/350z in the brake department. The offset may be different but other than that they are the same calliper. Just make sure you get the disks from the model the callipers are from.

I have a spare front seal kit for these these brembos if anyone needs one.

How similar are the Brembo brakes that came on 350Z's and R33 / R34's?

In the front they both run DB1520 pads and the rears run DB1521 - so if the pads are the same they they must be very similar.

The difference seems to be in the disk offset as shown in the attached link http://www.skylinesaustralia.com/forums/index.php?app=core&module=attach&section=attach&attach_rel_module=post&attach_id=41147

So the big question is:

Are the seal kits interchangeable as you can buy factory kits for 350Z's from the US for a very good price?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...