Jump to content
SAU Community

Happy Bday Saff!

Bec

By Bec,
in Victoria

 Share

Recommended Posts

saff_cossie Grand Master

saff_cossie

Posted
Posted

LOL! Thanks people! Yeah I normally keep it quiet, especially at my age!

Not sure about tonight. Was just going to get some food with Nic.

Mav, sorry did get your message along with several others so didnt get chance to reply as I have been driving all morning. :)

Link to comment
https://www.sau.com.au/forums/topic/139606-happy-bday-saff/#findComment-2602485
Share on other sites
saff_cossie Grand Master

saff_cossie

Posted
Posted

Had an excellent day and thanks for the wishes everyone. Have spent the afternoon washing the Evo and taking some pics with JW and his which I am sure will be posted soon. I am a bit of hack at washing the car so hopefully pics are in a good light.

Am open to suggestions if anyone is around tonight. Will grab some food now and open some wine but if anyone does fancy some drinks down this way, even Taco Bills in South Melb, I am up for it :laugh:

Link to comment
https://www.sau.com.au/forums/topic/139606-happy-bday-saff/#findComment-2603044
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • luke gtr
      Did tie rods. Steering now not "springing" back.

      By luke gtr · Posted

      Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • luke gtr
      Returning after a long time!

      By luke gtr · Posted

      I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • luke gtr
      Returning after a long time!

      By luke gtr · Posted

      Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • 33GTRV
      Rb26 iron block limit

      By 33GTRV · Posted

      Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...