Jump to content
SAU Community

Recommended Posts

Hey guysmoved to mackay 3 yrs ago bought a r32 gtst with a blown motor. Replaced motor but got mega issues. In the deep end for sure now but love the car cant wait to drive it when its going

Hey mate, welcome.

If you need any information, most people following this thread are very knowledgeable.

  • Like 1

Hey guys I have a problem. Replaced a blown rb20det with another. The new motor arrived with the timing out by 4 teeth. We re did the timing and got it running. But it is idleling rough as guts and the motor will die without throttle. If I give the throttle a tap it jumps up but then will go out of control. Up to 3 Grand then slowly comes back down. I have checked afm iac and cold start valve by unplugging them to see if I get a response. Which I do. I have power and signal going to all injectors and coil packs. All cylinders fire. The ecu has a ewad out of 55 which is no faults. Im out of ideas. Will do a boost leak test tomorrow with soapy water. SO CHEAP! Thanks in advance guys

Hey mate, seems like you have most of the bases covered. Usually the best way to test for leaks is to pressurise the intake.

If you are handy with a welder, weld a compressor fitting onto a piece of pipe with a tap, and weld the end shut. Them simply remove your AFM and clamp it there and slowly crank the pressure up to 30psi.

It is by far the only accurate way to find leaks.

Hey guys did a pressure test on the intake and I have a blown plenum gasket  the supplier I bought it off has a start up warranty on the motor the fact that this was already present has asked for a quote to fix and get the motor running. Lesson: warranty is awesome

Hey guys did a pressure test on the intake and I have a blown plenum gasket  the supplier I bought it off has a start up warranty on the motor the fact that this was already present has asked for a quote to fix and get the motor running. Lesson: warranty is awesome

looks like ur lucky there mate

After a new clutch cylinder for my car. (P/N: 30620-21U23)

Going to try Brakemart, Repco and Bursons, but just putting this up in case these fail and anyone has one lying around

Its a 3/4 Nabco slave, believe they might be the same as R32 ones, but not 100% sure

Hopefully should be able to source a new one anyway

Really? I dont go there that often. And I always forget to use my racq card anyway lol.

Ended up getting my slave honed and re-sealed by Better Brakes. They had it done in about an hour as well. Looks all shiny and new now :)

Works as well which is a plus

They were originally going to re-sleeve as well but said the bore didnt end up being that bad.

was just shy of $50, noone seemed to stock a new one. Was about to try nissan but dare say it would have been $100 plus

I don't think a re-sleeve would have cost much more, said it was going to be stainless re-sleeve so should last longer, but I'm happy as with the result. Like I said, looks like a brand new one after they sand blasted and re-kitted it

Have a funny feeling it might drive again tomorrow :)

I quite like 34's in yellow

get the wallet out Sean and just do it :P

Get the impression that this is really well looked after as well, has only been lightly modded. Would be a good one

Edited by 89CAL

If you're buying a BNR34 fro Qld, let me know. I know a few of the Brisbane bmr34 guys and they can give me the down low on the car. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...