Jump to content
SAU Community

Recommended Posts

Recently i did all the plastics for my mates 34,heres some pics for you guys that wanted to see what a black colour would look like.its called saturn black its also heat and chemical resistant. theres some befores and afters in there too.

post-38410-1212382807_thumb.jpg

post-38410-1212382865_thumb.jpg

post-38410-1212382923_thumb.jpg

post-38410-1212382971_thumb.jpg

post-38410-1212383033_thumb.jpg

post-38410-1212383072_thumb.jpg

  • 5 months later...

has anyone done this on a r34 with the popup screen? What extra steps are involved if anyone knows ???

Also does anyone know a good shadow silver/charcoal paint colour? I don't wanna do it up in black so as to leave a bit of contrast (like the original)

Oh and does anyone know if you can replace the led/light inside the radio/AC Unit ? my dash leds are blue and the radio/ac are green so I'd like to change these to blue as well when I take all of it out

Jack, any chance of taking a couple of piccies of your mates interior now with all of it back in place? Good work by the way, wish I had mates like you :P Cheers

Edited by Delta Force
has anyone done this on a r34 with the popup screen? What extra steps are involved if anyone knows ???

Also does anyone know a good shadow silver/charcoal paint colour? I don't wanna do it up in black so as to leave a bit of contrast (like the original)

Oh and does anyone know if you can replace the led/light inside the radio/AC Unit ? my dash leds are blue and the radio/ac are green so I'd like to change these to blue as well when I take all of it out

Jack, any chance of taking a couple of piccies of your mates interior now with all of it back in place? Good work by the way, wish I had mates like you :banana: Cheers

In my first post I've got a recommended colour for the plastic, go to supercheap and check it out, it's a good match :)

Recently i did all the plastics for my mates 34,heres some pics for you guys that wanted to see what a black colour would look like.its called saturn black its also heat and chemical resistant. theres some befores and afters in there too.

So you sprayed them all white as an undercoat, and then used the saturn black as a 2nd coat??

  • 2 weeks later...

What about those duplicolor brands.. are they any good? they have the pewter color that matches nissan sonic silver which the guy from autobarn showed me from the book.

Do you Guys spray clear coatings after applying the paint?

I used 3 coats of clear coat on the trim parts I painted. A bit overkill and when the sun was out the gauge cluster would reflect a bit onto the windshield

would probably need 2 coats max for the gauge cluster, put as many coats as you like on the rest :(

I posted these somewhere before but here's my effort:

DSC04159.jpg

DSC04259.jpg

DSC04265.jpg

I used powerplus paints too

Edited by Yo-Yo

hey guys, how do you take off the aircon surround??

hmm okay i had a look at it,

aircon is gonna be a tricky one to do with the red & blue temps around the dial which i want to keep.

ill do everything else tho.

see how i go

good to do over the xmas break :)

Edited by dori32

looks very nice .. I'm gonna do the same to mine but do the vents and aircon and perhaps the top lcd cover (I have that popup screen) in black. Then find some nice silver pedals and a silve bezel insert for the console and the car shouldn't look so 1998 anymore (maybe a bit more like 1999) :banana:

Speaking of which I'm going to go and rip out my (broken) lcd now ..wish me luck!

Edited by Delta Force

ok whatever you do don't use SEPTONE paint/primer .. this shit is just evil, I wasted 4-5 hours only to realize the paint itself is a POS. Will go looking for Powerplus paints tommorow.

i wanna do mine but the only thing that worries me is the AC controls. the blue and red thing around the knob did you guys just tape it up and spray painted the whole thing???

and can some one provide a step to step process and dismantling the ac unit???

the whole centre console (ac, stereo etc) slides out .. it's just 4 screws holding it in there. The blue/red on the AC is piss easy, just take them out as well as the clear plastic and spray the rest. Then glue them back in afterwards, it's no big deal trust me.

yeah it's all just clipped in ... the only thing you should be careful about is removing the vents - use a thin screwdriver from the left hand side and they'll pop out too. Make sure to protect the corners with masking tape to avoid accidental scratches when poping out vents and sliding out the console etc

To reveal the 4 screws holding it all in place, remve the gear shifter surround (pops out once you remove the screw behind the ashtray) and the vents - don't try removing any other fascias whilst the console is still in there. The vents will reveal the remaining 2 screws.

Edited by Delta Force

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...