Jump to content
SAU Community

Recommended Posts

A few weeks ago I had my R33 Skyline Diff Shimmed By Ray at RE Customs.

Prior to this my diff would always single spin, so I was looking for a solution to this.

My original thought was to buy either a 1.5 Caz diff or I was also looking into the Nismo 2way.. Both of the mentioned diffs were approx $1500 - $2500 installed so some big dollars.

After speaking to Ray about some possible options he suggested that I could add “shims” to my original single wheeling Nissan Diff to tighten it back up and all for a very affordable price. (Under $400)

The diff can be tightened up using various shims in the diff as per the list bellow:

0.80mm

0.85mm

0.90mm

1.01mm

1.05mm

1.10mm

1.20mm

1.30mm

1.40mm

1.49mm

Based on the selected shim you get a various desired tightness to the diff.

I asked ray to make my diff tight so it was something similar to a 1.5 – 2way Diff.

This was achieved by placing 2 shims additional to the original ones (1 on each side) 1.10mm thick to the diff.

This in turn has come close to locking my diff.

All I can say is its fantastic!!! This is also a very cheap option to fixing a single spinning Diff, and I highly recommend it to those who are sick of a single spinning diff and want a cheap replacement and fix.

I will also add that I am not one for doing things cheap but this does not appear to have any bad affects and is still using the original Nissan gear.

I took the car for a drive on the weekend and through some tight corners

Felt like it was on train tracks. The whole car now feels extremely stable so it has certainly been a viable performance upgrade.

If you’re interested in having this done to your car, speak to Ray at Re Customs and he’ll be able to give you a price and book you in if interested.

Re Customs - 9548 3414

Link to comment
https://www.sau.com.au/forums/topic/164346-fixing-your-single-spinning-diff/
Share on other sites

i wonder how it would work on the vspec diff

as i can lock my diff on demand via a switch

so it could be a tight locker on demand

the problem i found with my one is that its a weak lock when it does

hmmm thinking to do...

shims arent a good way to tighten a diff :P

speak to a good reputable diff specialist n he should refuse todo it

i heard this, looked into it, asked for it to be done almost got sworn at... said a good set up tightened lsd shouldnt need to get shimmed ...

so perhaps look into doin a job properly :O

or ...

just weld it up and be done with it ... chirpy chirpy chirpy

From what I've read it lasts about 2 weeks....
shims arent a good way to tighten a diff :D

Really?

Racepace did mine years and years ago now. Before i pulled my car off for the RB26 motor conversion.

The diff did approx 12,000km's (9-10 months) which included lots of burnouts @ the drags as i was racing every 2nd or 3rd week :)

Lots of dyno work, street duties any anything else you car to think of.

Certainly worked ok if you ask me :cheers:

Really?

Racepace did mine years and years ago now. Before i pulled my car off for the RB26 motor conversion.

The diff did approx 12,000km's (9-10 months) which included lots of burnouts @ the drags as i was racing every 2nd or 3rd week :)

Lots of dyno work, street duties any anything else you car to think of.

Certainly worked ok if you ask me :cheers:

We dont just shim it, Ash.....:D

We re-machine it, add more clutch plates (most important) and then reshim... they then work really well and last.....

cheers

Ben

We dont just shim it, Ash.....:cheers:

We re-machine it, add more clutch plates (most important) and then reshim... they then work really well and last.....

cheers

Ben

Well, there you go.

This is why i pay you a great % of my pay each year :D

We dont just shim it, Ash.....:cheers:

We re-machine it, add more clutch plates (most important) and then reshim... they then work really well and last.....

cheers

Ben

Is this similar to what you do to the transfer case in the GTR's? I hear from Jack that the re-shimming you did on his, did wonders for his handling on track.

Cheers.

Nick

We dont just shim it, Ash.....:)

We re-machine it, add more clutch plates (most important) and then reshim... they then work really well and last.....

cheers

Ben

Ben, any idea on what sort of $ are involved in this? I hate my single spinner! PM if you'd prefer.

BTW - Car is 100% after your work. Top job :)

We dont just shim it, Ash.....:)

We re-machine it, add more clutch plates (most important) and then reshim... they then work really well and last.....

cheers

Ben

hey ben

would it work the same for the vspec diff?

i have a switch to hard run the vspec pump so i can lock it on demand.

would shimming and changing the clutch in it make it really tight but only when the pump runs?

if so... can you quote a price? (or via pm)

I shimmed my stock VLSD diff which worked well for getting the power down on corner exit BUT in a straight line in first gear the left wheel would always single leg it, second gear would have a slight squeel from usually the left wheel and when the diff was cold second gear would spin up a single wheel as first always would.

I eventually got sick of the lack of traction in first gear and picked up a well priced R32 GTST diff that runs a GTR/GTS4 mech center with nismo 5 bolt axles.

It handles 100% better than the shimmed diff, much much more predicatable. It gets the power down much better/smoother out of corners and no more single spinning through first.

At least now I have an incentive to throw on a set of good tyres. Last time I threw on a set of good toyo's the left rear tyre wore so so much quicker than the right. :)

Shimming the VLSD is good for drift; pretty much for nothing else unless you preload it to the point of the spider gears completely binding. May as well weld it. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...