Jump to content
SAU Community

What Rims Do You Have On Your Stagea Or Would Like To Get?


joshsmum00
 Share

Recommended Posts

nismo lmgt2 18x10 +20 all round, yet to be fitted as i have to install the autech cradle to make them fit properly without scrubbing on rears. I have the cradle just need some time to put it in, the car currently runs 33 gtr rims and i think they look alright though fronts could do with a 20mm spacer to fill the gaurds, rears are perfect with normal rs4 cradle.

Link to comment
Share on other sites

i really dont know.. i was thinking a very dark bronze but i'm not sure.. i'm gonna have to do a bit more deciding

and then maybe photoshop them on MY car :P

I've said it before and I'll say it again, Takata Green when going for TE37's. HOT! (Especially on black)

greente.jpg

Link to comment
Share on other sites

I've said it before and I'll say it again, Takata Green when going for TE37's. HOT! (Especially on black)

daymmmmmmm i dunno if i like black and green in the same boat..... maybe i need to go for something a bit more bling and chromeish but still a 5->6 spoke design.

i saw something else i like.. the Enkei AKP and the RP05 ..... anyone else got them? like them? thoughtS? :P

akp_blk.jpgrp05_sbc.jpg

Link to comment
Share on other sites

^^^

p1.jpg

it looks like the S2 260RS front bar just wasnt enough of a PITA for this bloke, he had to add another lip to it.

i remember my old stag was a nightmare and it wasnt low like this one.

Link to comment
Share on other sites

that add on lip is quite popular for the 260rs bars in japan and alot of the guys run them (plus lower ride height) i think it's an r34gtr lower lip too

low cars aren't that hard to get about, becomes second nature, but tests your patience at times :)

Edited by M I K E
Link to comment
Share on other sites

always wanted to know what they would look like on a stagea. you wanna be tester >?

I might be a tester for these in 18x9.5 +30. Will be tight on the rear

The 9.5 have the deep dish. 8.5 have mid dish and 8 have low dish

Pis is of 9.5 +38 deep dish

If I do not like them, they will be up for sale a bit cheaper :)

Just waiting the the exchange rate to rise a bit.

post-14923-1252277706_thumb.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
    • Thanks for all the replies! I also wanted to ask if wheels that were fitted on Ford Falcons would fit the 350GTs as well? In the area I'm at there aren't that many options for secondhand wheels and new ones here are way out of my budget. From what I've seen, most of the wheels that are available that were fitted on Ford Falcons have an offset of +33 to +36, with a centre bore of 70.5mm whereas the stock 350GT's ones are 66mm, can't seem to find any hubcentric rings that fit that difference though. 
    • 215/45/18 tyres are probably a little on the low side compared to the factory tyre, it should be closer to a 245/45/19, which will get you about an extra 11mm of height, and should make you speedo read a bit closer to reality. 245/45/19s will be a bit too far the other way and you risk a speeding ticket as your speedo might read slower than your actual speed.  245/40/19s would be correct if you are going to 19in rims, they will give you a similar total diameter to the 245/45/18 tyres.  
    • That's something I forgot to put in my list. The aggressive anti-squat in R32 is a f**king menace. I still need to decide if I'm going to drag the subframe out of my car and weld in the GKTech corrector kit. The main reason to dither is the need to switch to spherical joints in the lower arm to account for the twist induced in the rear pivot caused by lowering the front pivot. And yes...we do put better subframes in R32s, and I wish I'd gotten an S14 one instead of an A31 when I did the "take off and nuke it from orbit" HICAS delete all those years ago.
×
×
  • Create New...