Jump to content
SAU Community

Recommended Posts

Thanks guys... Especially for putting up with this on a Skyline site!

As for the specs...

The 1968 chassis is radically customised, 200mm widened so it has the same footprint as a Porsche 944/968. I've used parts from a 1994 968 Porsche to do the rack and pinion steering conversion, a-arm/mcpherson strut front end, and the IRS rear end. Brakes are 986 Porsche/brembo 4 spots all round. Wheels are from a 996 and are 18x8 and 18x10's. Bridgestone RE55 rubber. Coilovers are Tein super streets... yet to sort out the spring rates and valving. The gearbox is from a 911 turbo, axels and CV's are 968. Clutch is a custom twin plate that will support around 500hp.

The core body is a 1966 shell and is mostly stock except for the single piece glass and power windows. All the rear windows are plastic for weight reduction. Door linings, dash and the floor of the car are all made from carbon fibre sheet material. Guards are custom made fiberglass. The firewall is a 2 piece bolt in aluminium job, and is extended forward to allow a lot more driveline/engine to fit in the back end. The entire back end of the car is removable and unbolts to allow full access to the rear suspension and engine. Air intakes for the turbo's are ducted from the rear quater windows.

The engine is entirely custom and is based on a VW water cooled die cast aluminium block, but is converted to air cooled. It is bored and stroked to 2.5lt. Induction side there is a pair of 8cm trust T517z's and PWR 600hp water to air intercooler. Oil system uses an external RPM 4 stage dry pump. The oil tank, coolers and battery are mounted at the front of the car for better weight distribution. The engine runs a distributorless 4 coil MSD igniton with a AEM CDI. Fuel injection with a Wolf V500. Air cooling is based on a 911 turbo setup with a carbon fibre cooling shroud.

And a video of the engine running. If you have good speakers crank them up!

http://www.youtube.com/watch?v=W_P2mtkncNM

And 2 more pics.

DSCF0132.JPG

DSCF0136.JPG

Cheers,

Ian

We have been playing with bump steer adj over the last little while. Typical me, "can't be that hard to make". MkI was pretty basic and worked well...... until there was a big excursion at speed hitting the back of a ripple strip at an odd angle. Result below.

Picture094.jpg

So then the thinking was we would try a commercially available option. Just Jap sent these ones that were cool but way to short. My brain did its usual trick and put me infront of the lathe again, And this is what came out after 2 0r 3 nights of toil and frustration. 9Mine left, JJ right)

Picture093-1.jpg

And fitted in the pig. I'm slightly ashamed to admit, Its a Toyota. With all Nissan underpinnings!!!!

Picture091.jpg

3538480432_4442aa60b9_o.jpg

That is a nice bit of engineering Noddy. Have you made similar roll centre changes to the Yellow R33?

got mine back on the track this weekend, the guys at UAS did a great job. 150+ laps flat out without any temp problems. Basically the only time we stopped was to refuel it.

wp-100717.jpg

next up is a 1 hour race at wakefield in 5 weeks

great news dundan! good luck for the 1hr mate. :ermm:

  • 2 weeks later...

Here's the shed on Christmas Morning.

I hung a shed key on the Christmas Tree and when all the presents were gone I pointed it out to my 8 year old son and played "hotter colder" with him til he found it.

I've now upgraded to an Arrow AX9 too.

post-41741-1282090587_thumb.jpg

Here's the boy at Monarto Go Kart Track

post-41741-1282091321_thumb.jpg

Here me at Mallala I've now added some cusco goodness to keep it a bit flatter.

post-41741-1282090662_thumb.jpgpost-41741-1282090718_thumb.jpg

post-41741-1282090387_thumb.jpg

Very cool mate. I'd love to have received a go kart under the Christmas tree!

So would have I, now I have to live all my motorsport dreams through him.

I suppose it could have been worse for him, I could have been into Stamp Collecting.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If we're going after market gauges, I'm a big fan of Australian made... Get some RedArc!
    • Unless you're fortunate enough to buy a newer car, getting an older style plate to match your name/car is difficult because they've already been purchased.  Unlike other countries, personalised plates are locked to the country and not region, so there can't be multiple versions of the same plate but with a different area code.  Hope that helps
    • People use the numbers to make it look like letters to spell words/names, which is where the illegal spacing comes in. For example this GR Yaris  
    • Today's rock removal from my stock pile out the back into a 4m³ skip bin, I still have a bit to go, hopefully there's enough room in the skip bin, it will be close My daughter and her boy was coming on Sunday to help, but, I got possessed by demons and started work as soon as the bin arrived at 1230 today Lots and lots of barrow loads were achieved  Currently I'm sitting on the lounge drinking beer thinking of how I should have waited till Sunday for some help, tomorrow will be a day off, in saying this, my day off will involve prep and paint of my alloy coolant and PS tanks with wrinkle paint (Jackie is in Sydney till Sunday so the home oven will get a run curing the paint....LOL)
    • That's why I said it is a meaningless term. Because there is more than one meaning that people can apply to it. When we said "highflow", that is exactly what we mean, and exactly what is done. In a highflow, they take your housing and machine them out to take bigger wheels, have a better internal profile, etc etc, and fit a new core with the different/better/bigger wheels.
×
×
  • Create New...