Jump to content
SAU Community

Recommended Posts

  • Replies 812
  • Created
  • Last Reply

Top Posters In This Topic

yeh, but you have to run a divider plate between the engine and the bonnet over the radiator support.

dont worry Jase, you will see... :banana:

wouldn't that suck major hot air unless there was a cold air feed?

hmmmm, yes, very nice. The Carbon Fibre is a bit overkill though, and tune lenght intake runners will be expensive i dare say. Harrop do one also but 12k

Hey Stu, go get some Kleenex for cleanup. You're gonna need them.
hmmmm, yes, very nice. The Carbon Fibre is a bit overkill though, and tune lenght intake runners will be expensive i dare say. Harrop do one also but 12k

Harden the f**k up. Here's the same manifold with Al tubes.

LS7Xram_AlumTubes_4web.jpg

my s13 needs an ls1 just so i can fit that manifold.

But i reckon i can make the throttle linkage more complicated :ph34r:

Very interested to see how this car goes. You only need to better a 1:07.9 at wakefield and you are quicker than my old r32. I reckon your car has 6's in it without too much trouble, probably quicker with a bit of seat time.

yes, im all over it brother, Aaron has already quized him on runner lengths which will blow your mind.

they are also doing me some CnCd rocker covers which are trick.

Stu, I would quiz Jamie from NRE on how these are set up. They do the ones for Ingall etc.

_products.htm

Edited by BezerkR32
yes, im all over it brother, Aaron has already quized him on runner lengths which will blow your mind.

they are also doing me some CnCd rocker covers which are trick.

Saw pics of the covers on the PRI show website. Awesome!

post-695-1227042708_thumb.jpg

not heaps to report. have been chipping away at the long list of little fidly jobs like mounting ECU and com port, fitting temp senders, gear shift boot, tow hooks, etc. heaps fidly and time consuming but has to be done. have some second hand rubber on those rays datonas and they look good. scored some second hand semi slicks of one of the brut utes. the biggest i can fit on the front is a 235. have a 245 comfortably on the rear. going to get wired soon. even put engine oil in it today so very close.

A little more done. I have fitted the LS1 wiring harness and ran it into the car to the ECU which is mounted on the passenger floor. Mounted com port plug in pasenger air vent. modified the harness and moved the position of the o2 sensor plugs as they were mounted further down the exhaust before, now they are in the headers.

brakes are bled, clutch also. fluids in engine, trans & diff.

Modified the steering knuckle a little just to get a bit more clearance. had to relieve passenger engine mount also. had to pump the trans tunnel around the shifter opening also.

Radiator, thermo fan and hoses all plumbed. Temp sender was fitted in cylinder head.

Tow hooks fitted front and rear.

Fitted diff pineapples, waiting for front & rear sway-bars to arrive.

Thats about it, going to get wired this week, then doing the tin work and fabbing a catch can and recovery tank and some ducting. Should get her back after Christmas.

post-20078-1228132129_thumb.jpg

post-20078-1228132219_thumb.jpg

Looks like you are soon finihed, and it is looking great! :rofl:

You must upload more photos and video clip from first startup... I want to hear it roar!! :laugh:

Do you have more pictures from the engine bay and interior? :no:

only whats already been posted, nothing much else has changed.

Looks like you are soon finihed, and it is looking great! :thumbsup:

You must upload more photos and video clip from first startup... I want to hear it roar!! :D

Do you have more pictures from the engine bay and interior? :)

Does look great, though looks wierd not having anything hanging out through the opening in the bar. May have to glass it back to teh radiator so you dont see light through there.

Tell me where to write a 10k checque for the conversion and i will post it off....only i know it woudl cost way more then 10k ;)

All it needs to be truly toss worthy is a close ratio box and a big silly cam to make the thing nice and peaky and make good top end. LOL, i seem to like spending money making cars slower ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...