Jump to content
SAU Community

Recommended Posts

spotted me taking a heap of shit work truck through regency for roady today.

was on double defect and they passed it.

are they getting more lienient atm or was i just plain lucky?

also seen a silver 32 broken down on pt waikfield rd cavan. hadnt even pushed it off the rd and no hazaeds on.

he was just sittin in it looking like he was chattin to someone inside with no care in the world.

good one.

white 32 with dark wheels at the seaford tav last night and also turning onto griffiths drive about 3pm

white 32 gtr 'gtr 094' behind me in the hj's darlington drive thru just after 3.30 today

Today spotted

White 180 on cross rd followed for a bit b4 he pulled in to maccas

Silver Cef on states.... Mmmmm sexy

White RX7 S5 on Panatalinga, clean as

Yesterday

Purple Sileighty back streets of edwardstown

White 180 on the back of a car trailer towed by a 4x4 near glenside

Spotted red r33 gtst on beach rd round 1ish heading towards the beach..

Purple r33 bottom of cement hill round 2...

White r33 turning onto sturt rd off Brighton rd round 2:10 with kit,exhaust,black face rims..

Saw a grey 32 on anzac stopped by the 5-0 at 4:30. Also saw heslo at AJD. Shot a few photos before i left. Missed almost all of it. Damn!

Saw this car as well, then a bit later going south on Brighton Rd .. Female driver, I think?

All sunday.spotted chad yesterday down at brighton, stag =wub.gif

A white 34 fourddoor with a blackbonnet going along taplies hill, closley followed by a yellow twodoor 34.

Bayside Blue GTR on the floooor with some dope fitment on diagonal road going towards glenelg woot.gif

''iculkn black stag parked down my street yesterday . same one I think from supercheap darlington ???

showroom new R32 GTR , black one on south rd near onka river heading south, car was flawless

white r31 with P's and burnout rims on rear of it coming out of aldinga about 4pm , blowing a bit of smoke and sounded like hell.

every tool in town doing doughnuts and drifts up the hills from me last night. annoying pricks take it to a track !!!!!

All sunday.spotted chad yesterday down at brighton, stag =wub.gif

A white 34 fourddoor with a blackbonnet going along taplies hill, closley followed by a yellow twodoor 34.

Bayside Blue GTR on the floooor with some dope fitment on diagonal road going towards glenelg woot.gif

I didn't know i was you from a distance because of the stock spec rims...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...