Jump to content
SAU Community

Recommended Posts

Received the bolts Dirt Man ;)

Went to Nissan today and got some new keyways and flywheel bolts.

The boys are coming round tonight so we are giving it a red hot go, engine "should" be in tomorrow.

Car is booked in at Adams for a full E85 tune on the 11th. I need to find a surge tank and 044 before then ;)

Jim was reluctant to fit the Autronic to my car...but he's tuning yours...no love.

The tune in the unit now is Guilt-toy's RB25 tune...may have been better loading mine in.

He needs to bridge the TPS signal to the ATTESSA ecu to give the car 4WD.

Im reconditioning your CAS...i think the noise was from me cleaning it and the gasket not sealing the unit properly (no fault of yours)

Well, you know where im working currently so guess who spoke to Jim...

Ok cool, how exactly do i bridge it in?

Good news on the CAS

Well, you know where im working currently so guess who spoke to Jim...

Ok cool, how exactly do i bridge it in?

Good news on the CAS

pin 56 on the ecu to the tps 0-5v input on the attessa unsure of the pin number

Received the bolts Dirt Man ;)

Went to Nissan today and got some new keyways and flywheel bolts.

The boys are coming round tonight so we are giving it a red hot go, engine "should" be in tomorrow.

Car is booked in at Adams for a full E85 tune on the 11th. I need to find a surge tank and 044 before then ;)

we have an 044 spare

Engine has most its bits on it, minus lines and some turbo bolts.

So its looking good for engine and box install tomorrow, might even turn key tomorrow night.

Thats if the new manifold lines the turbo up with my dump pipe :P

Engine in :(

But i need a new started motor, what a bloody anti climax :P

And boy the car needs a damn good wash. Dust mixed with oily fingers and hands all over it. Engine bay needs a good detail too.

Anyone know where i can get another starter motor ASAP?

How much to get it recoed?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...