Jump to content
SAU Community

Spotted Thread


paulr33

Recommended Posts

Sounds like ive been spotted, but ive only got a GT... My car hasnt hit puberty yet! LOL (If you saw a green magnetic p plate on the boot, that was me for sure)

Ha nah I was going the other way at 100, spotted your car in slow traffic. I always lol at everyone going the other way in stop start. :thumbsup: then spotted your car sittin there.

Link to comment
Share on other sites

Ha nah I was going the other way at 100, spotted your car in slow traffic. I always lol at everyone going the other way in stop start. :D then spotted your car sittin there.

just cause you have to travel the opposite direction of the peak hour traffic... :thumbsup: ..not fair...hate traffic....

Link to comment
Share on other sites

Saw a black R34 GT-T at Eden Rise in Berwick today with the plates [R34NRG].

He was parked to my left. To my right was some unknown white car that hit me while reversing out and drove off without leaving a note... My car is only six weeks old and now it's damaged.

Link to comment
Share on other sites

spotted a yellow r34 gtt on frankston dande road this morning, thought it might have been charles, but didnt see any carbon on the rear..., standard number plates to from memory

everytime i see a yellow gtt, i think of charles.

Link to comment
Share on other sites

spotted a yellow r34 gtt on frankston dande road this morning, thought it might have been charles, but didnt see any carbon on the rear..., standard number plates to from memory

Use to see that one a lot, works on frankston dandy rd at the end of abbotts rd.

Link to comment
Share on other sites

Saw a black R34 GT-T at Eden Rise in Berwick today with the plates [R34NRG].

He was parked to my left. To my right was some unknown white car that hit me while reversing out and drove off without leaving a note... My car is only six weeks old and now it's damaged.

That car park in Eden Rise is to tight..

Sorry about your car.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
    • Just did this job on my 32 with the boost doc kit. was quite simple to fit, hardest part was getting the rubber bungs back on the firewall. does anyone know how the heater will work now without the flap in the bend? Will I just have a heater on 24/7 now?
×
×
  • Create New...