Jump to content
SAU Community

Recommended Posts

  • Replies 136
  • Created
  • Last Reply

Top Posters In This Topic

has anyone come across the corvette communities reaction to this version in relation to the ZR1?

Nope. But im sure i can help fill you in on what there most likely saying

" nissan is cheating , blah blah blah, the time isnt official , the zr1 had a passanger in it, its still a datsun , its still a ricer " lmao

Denial can be an ugly thing

A friend tells me that in the Porsche forums they say when the GTR was driven second against it in a test drive, the driver had learnt the track better. In another test where the GTR went first, it supposedly kicked up rocks and junk on the track which affected the Porsche's run.

lol

very interesting! i doubt NISSAN would raise the power outputs to over 600HP due to the Plasma coating, which supposedly is good for up to only 600hp or so.

If the current GTR is a "mini veyron", then what would the VSPEC be?? :rofl:

A friend tells me that in the Porsche forums they say when the GTR was driven second against it in a test drive, the driver had learnt the track better. In another test where the GTR went first, it supposedly kicked up rocks and junk on the track which affected the Porsche's run.

lol

Bahaha , i spat my water after reading the 2nd part

no GTRs are auto..

DSG is not an auto

technically not auto, but in still pretty auto.

I'll rephrase the question, just in case you had difficulty trying to comprehend what I was asking :(

Is it manual?

Edited by IOWNU

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...