Jump to content
SAU Community

Recommended Posts

Gee by the time I get my car 100% there's gonna be 100 new better turbos available.

Keep up the good work Stao!

If its off the car you can send it back to me for a update. The main difference in the SS2 would be the Type B rear housing and compressor housing.

Just came back from Drags :)

Very very happy

I can confirm its driver error that's causing my low times.

I think i could get a low 13s ( or a better driver )

Got a 13.822 @ 171.3km/h

Around a 4k launch

FYI

ATR45G2.5 is my turbo @ ~340hp

Just came back from Drags :)

Very very happy

I can confirm its driver error that's causing my low times.

I think i could get a low 13s ( or a better driver )

Got a 13.822 @ 171.3km/h

Around a 4k launch

FYI

ATR45G2.5 is my turbo @ ~340hp

Low 13's is definately possible, however 106mph means you aren't anywhere near 340rwhp.......

What have you changed in this new ss2.5? Is it a turbine change?

PM me if you would prefer

That BB SS2.5 has a larger turbine, that is only good for high flowing use. getting it back on the dyno Monday. The prototype SS2 had a different set of blades, making minor changes to boost ramp behavior.

I ran that exact time and speed with an S14 making 175rwkw with stock turbo.

my 60' was 1.8.

Unless your 60' was like 2.2 or higher and you missed gears a couple of times, it will be more than driver error that's the issue.

I ran that exact time and speed with an S14 making 175rwkw with stock turbo.

my 60' was 1.8.

Unless your 60' was like 2.2 or higher and you missed gears a couple of times, it will be more than driver error that's the issue.

Wow that's a huge difference in power

How much experience did you have prior to this run?

I don't know about 115mph, but 106mph is way low for ~250wkw. Quite an odd pattern forming!

Not wrong there, all the drags results are showing that you would be better off with a stock turbo.

Wow that's a huge difference in power

How much experience did you have prior to this run?

First and only time at drags.

Got 4 runs.

first one was a 14.4 then eventually got 13.8 on the 4th run.

I kept shifting at 7K (silly in an SR) and would just touch the rev limiter in 3rd as I crossed the line.

Could have possibly been quicker if I shifted earlier but never got to go back.

Car was a series 1 S14 with heavy 17s.

255s on the back with pressure reduced to about 22psi

Stock Clutch, FMIC, 1 bar boost, pod, exhaust and tuned SAFC II

Done by Yavus at Unigroup

175.4rwkw

Stock turbo and clutch do make it easier to launch more consistantly though.

And the SR20 is a different torque curve to the RB so possibly easier to control wheel spin.

Edit - I should take my current car (stock RB25 R32 gtst) to get some base times.

Edited by TTT

I don't know about 115mph, but 106mph is way low for ~250wkw. Quite an odd pattern forming!

Seems to be pretty normal

I did 13.32 with 112Mph that was stock weighted R34 with a pu high flow 280rwkws on street tyres. Stock turbo run 14.6 with 98mph on 12psi with 200rwkws

Edited by GeorgesR34

Seems to be pretty normal

I did 13.32 with 112Mph that was stock weighted R34 with a pu high flow 280rwkws on street tyres. Stock turbo run 14.6 with 98mph on 12psi with 200rwkws

Just to show you how off your figures are. My non turbo 300ZX trapped 97.6mph with ~130rwkw, yet your R34 had "200rwkw" ;) Trap speed tells no lies

Can a turbo perform better on a dyno than on the road?

Like could two turbos that makes 250rwkw with the similar power curve get totally different results on the road.

Very easily, what i don't understand is how these turbos keep underperforming on the drag strip.

Edited by Super Drager

Just to show you how off your figures are. My non turbo 300ZX trapped 97.6mph with ~130rwkw, yet your R34 had "200rwkw" ;) Trap speed tells no lies

Punching your 97.6mph trap speed into a drag strip calculator - to only have ~130rwkw you would need to be weighing around 1315kg - the 300zx non-turbo (from my googling around) is around 1460kg without a driver. That's not an insignificant weight difference. Not questioning you - just curious :)

Was going to say that - my Prelude needed around 130kw to pull 96-98mph trap speeds and weighed ~1330kg as raced, must be an ultra low reading dyno to do 97+ with a "130kw" 300ZX.

I'd hope for over 98mph with 200kw in an R33 too, though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...