Jump to content
SAU Community

Recommended Posts

Some updates. This is in relation to the ATR43G3 turbocharger. This prototype runs our latest rear wheel, how ever I will be installing it into a smaller rear hopping for more power while retaining the same drive ability.

comp.jpg

Test car is currently on E85, the goal would be 350rwkws+ on 20psi with full boost reached by or before 4000RPMs. In which should achieve 300rwkws at 20psi on pump 98 fuel.

Results for above:

power.jpg

boost.jpg

I usually make a base model and tune it against its older version. If it is a success then integrate the SS compressor for better response. So both models gets upgraded.

Sorry I didn't get any names in the package, I assume you are the guy from WA correct? if so then yes it has been received. just more power in this upgrade?

Crap i forgot to stick that on the box >.<

Sorry.

Yeh, newer profile like the ss2.

Then if you can send it off to scotty for External goodness

Also PM me the money you need.

Edited by jay-rod

im trying to find some ss2 graphs...

What power would be expected from a ss2 running e85

6boost mani

External waste gate

power fc

z32afm

no exhaust

1000cc injectors

plazmaman plenum

front mount

Excellent, i didn't think it would become that much of a restriction. Good news!

Also, sorry for such a noobish question, but what size is the rear housing on the SS2? .82?

I said external gate in the first post!

God damn i am getting ridiculously keen for this! RB25/30 NEO + 6Boost + TiAL + ID1000 + E85

My poor bank balance :(

  • Like 1

I said external gate in the first post!

rajab damn i am getting ridiculously keen for this! RB25/30 NEO + 6Boost + TiAL + ID1000 + E85

My poor bank balance :(

you did so!

fuark I am blind.. been at work too long today

No the SS3 is about 300rpms laggier then SS2.

The power / response trade is: 1KW:10RPMs.

Take the SS Alpha trailed for example:

SS2 makes 383rwkws 20psi by 3500RPMs

SS3 makes 407rwkws 20psi by 3800RPMs

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...