Jump to content
SAU Community

Recommended Posts

The 53mm GTRS turbines don't work with RB25det engines very well.

The SAT stands for Special application turbocharger. This one is made only for Rb26 and Rb25 turbo engines working with large external gate setups.

We can high flow them to -5 or -9 depending on the HP chasing for.

With the damaged -7s I need to have a look at the turbo, the smallest billet wheel that I currently make is in 60mm that made 250rwkws on P98 on my SR20det.

The -9 idea sounds the go, what's involved in that and can it utilise the billet wheels

Also an idea on pricing, PM if needed

I have also posted in the Kando thread about fitting the 20.5g TD06SL2 onto a RB26 manifolds in twin form

Car is going in for tune next week with the 21U highflow and I can't decide which injectors to use.

I have a set of S15 440cc injectors (cleaned and flow tested) or potentially a set of used Nismo 740's.

If the 440's are enough for around 260rwkw (keeping conservative AFR's and safe injector duty cycle) I'll use them. If not I have to shell out for the 740's.

Car will be running PULP.

Car is going in for tune next week with the 21U highflow and I can't decide which injectors to use.

I have a set of S15 440cc injectors (cleaned and flow tested) or potentially a set of used Nismo 740's.

If the 440's are enough for around 260rwkw (keeping conservative AFR's and safe injector duty cycle) I'll use them. If not I have to shell out for the 740's.

Car will be running PULP.

Why not just grab a set of ID's/xspurts? They're pretty cheap and have a 725cc injector and have E85 capability should it become available near you. Not sure what a used set of 740's goes for but I'm sure the xspurts would only be maybe 100 or so more

Why not just grab a set of ID's/xspurts? They're pretty cheap and have a 725cc injector and have E85 capability should it become available near you. Not sure what a used set of 740's goes for but I'm sure the xspurts would only be maybe 100 or so more

I want to keep the factory side-feed rail for now.

The 440s will be at or above max to make ~260rwkW. Will do it, but will not have any of that safety factor you were after.

I guess that answers my question!

Hey,

Recently purchased the newer version of atr43ss2 (internally gated 17psi actuator)a few weeks ago. Vehicle has following mods :

Nistune

Dvs custom metal intake 3" with breather and returns

Factory air box with high flow panel

Z32

Braided oil lines

Jjr dump/front pipe 3"

Catco race car 3"

Turbosmart boost tee

Ngk-r BKR7E 0.8mm gap

Blitz return flo cooler

Nismo muffler

Nismo fuel pump

Id1000

Dvs jez tuned vehicle and was only able to safely make 230kw going from 18psi Down to 15psi.

Elimination tests:

Removed top of airbox and tune ( minimal gains)

Removed muffler and tune ( minimal change)

Checked boost leaks etc

Running shell 98

I'll get the dyno graph and other details when I pick up vehicle.

Dvs tuning advised may be the return flow cooler causing the issue.

Any advice. I'm stumped.

Check pressure drop across the cooler. I see this happens with certain model of blitz coolers. Also pre-load the actuator abit more.

Green is before cooler and the rest is after.

coolerrestriction.jpg

  • Like 1

Any idea on duty cycle at that power level?

That was about 95 DC at factory pressure, I have since upgraded pump and bumped base pressure up 5psi and car has since made 293rwkw with new rings and bigend bearings and HG on same boost level

95DC is not advisable, but I was trying to achieve something which I am 0.14seconds off :(

Edit : with the way I have my car set up it is very good on fuel and has got over 630km from a tank full

  • Like 1

Hey,

Recently purchased the newer version of atr43ss2 (internally gated 17psi actuator)a few weeks ago. Vehicle has following mods :

Nistune

Dvs custom metal intake 3" with breather and returns

Factory air box with high flow panel

Z32

Braided oil lines

Jjr dump/front pipe 3"

Catco race car 3"

Turbosmart boost tee

Ngk-r BKR7E 0.8mm gap

Blitz return flo cooler

Nismo muffler

Nismo fuel pump

Id1000

Dvs jez tuned vehicle and was only able to safely make 230kw going from 18psi Down to 15psi.

Elimination tests:

Removed top of airbox and tune ( minimal gains)

Removed muffler and tune ( minimal change)

Checked boost leaks etc

Running shell 98

I'll get the dyno graph and other details when I pick up vehicle.

Dvs tuning advised may be the return flow cooler causing the issue.

Any advice. I'm stumped.

when you say 'safely' make .... was the engine knock limited?

  • Like 1

Hey,

Recently purchased the newer version of atr43ss2 (internally gated 17psi actuator)a few weeks ago. Vehicle has following mods :

Nistune

Dvs custom metal intake 3" with breather and returns

Factory air box with high flow panel

Z32

Braided oil lines

Jjr dump/front pipe 3"

Catco race car 3"

Turbosmart boost tee

Ngk-r BKR7E 0.8mm gap

Blitz return flo cooler

Nismo muffler

Nismo fuel pump

Id1000

Dvs jez tuned vehicle and was only able to safely make 230kw going from 18psi Down to 15psi.

Elimination tests:

Removed top of airbox and tune ( minimal gains)

Removed muffler and tune ( minimal change)

Checked boost leaks etc

Running shell 98

I'll get the dyno graph and other details when I pick up vehicle.

Dvs tuning advised may be the return flow cooler causing the issue.

Any advice. I'm stumped.

3 things I see MIGHT cause you issues

1) JJR dump pipe ( this is a copy of the HKS item and that was never really much chop )

2) boost T will cause boost to tapper off

3) return flow cooler could be causing pressure drop, Stao has graphs of this from his GTR

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...