Jump to content
SAU Community

Recommended Posts

  • Replies 615
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

356mm front, 343mm rears...

Ben: I'll take some decent pics of the wheels tomorrow... Had LOTS of requests for them, but haven't really had an opportunity to take any.

No full floating/strap drive?

They are floating discs...

Strap drives are for road cars. They can result in warping when subjected to high temperatures...

Bobbin heads are much more suited to race applications, going by the many brake specialists who I spoke to...

They are floating discs...

Strap drives are for road cars. They can result in warping when subjected to high temperatures...

Bobbin heads are much more suited to race applications, going by the many brake specialists who I spoke to...

Ah, my bad, couldn't tell from the pics I assumed they were fixed/solid mounted.

Have only seen strap drive in the AP range, quite a few GTR's here in VIC run them.

Then again there are no hardcore race GTR's down here.. :P

Have you decided on what pads you're going to use?

Ah, my bad, couldn't tell from the pics I assumed they were fixed/solid mounted.

Have only seen strap drive in the AP range, quite a few GTR's here in VIC run them.

Then again there are no hardcore race GTR's down here.. :P

Have you decided on what pads you're going to use?

Yah, Strap Drive is an AP Racing innovation... Supposedly cheaper than the traditional Bobbin Head fixtures, but as I mentioned, more suited to road applications than high temperature track/race applications.

I'm no race engineer, and I can only really go by what I'm told... Which is why I seek out multiple opinions and reconcile data to make sure people aren't feeding me bullsh1t ;) But it isn't a foolproof method, so I'm more than open to what people on SAU think!

Using Ferrodo DS3000 front and rear at the moment... I'm sure that I'll be massively rear biased at it stands, so will play with pad setup and brake bias to fix it.

Yah, Strap Drive is an AP Racing innovation... Supposedly cheaper than the traditional Bobbin Head fixtures, but as I mentioned, more suited to road applications than high temperature track/race applications.

I'm no race engineer, and I can only really go by what I'm told... Which is why I seek out multiple opinions and reconcile data to make sure people aren't feeding me bullsh1t :P But it isn't a foolproof method, so I'm more than open to what people on SAU think!

Using Ferrodo DS3000 front and rear at the moment... I'm sure that I'll be massively rear biased at it stands, so will play with pad setup and brake bias to fix it.

I've got the same brake setup, but different brand. Have found that Pagid RS14's up front and Hawk HP Plus at the back work a treat - car is very well balanced under brakes. I found the DS3000's burnt up in 3 or 4 events. I'm getting 6+ events on the pagids, and have just changed the rears after 24 events.

I've got the same brake setup, but different brand. Have found that Pagid RS14's up front and Hawk HP Plus at the back work a treat - car is very well balanced under brakes. I found the DS3000's burnt up in 3 or 4 events. I'm getting 6+ events on the pagids, and have just changed the rears after 24 events.

Brilliant... Thanks heaps for that feedback mate!

Yeah, I used DS3000s in a previous GTR which I also gifted with CP5555 pistons, and they did wear out quite quickly.

I've heard good things about Hawk HT10 pads as well...

Andrew,

What time you leaving our area tomorrow morning mate?

Andy and I are meeting near Longueville Rd around 6:50am

I'm not planning on leaving that early mate :P I'll leave at about 7:30am I think... No rush to get there ;)

Yah, Strap Drive is an AP Racing innovation...

Performance Friction did it first, AP copied and called it a different name :P

Race cars dont have the same problems as they went to carbon rotors (typically) which dont have the expansion issues of steel rotors. In classes where they are forced to still run steel rotors you will find that manufacturers all run different types of floating hats

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...