Jump to content
SAU Community

Recommended Posts

Just got a phone call from the guys at Boost Magazine, I entered a competition at Compak Attak by subscribing to Boost magazine for a set of Kelford Cams and I won!

Woohoo!!

Details of the cams that are available to me are here..

http://www.camshaftshop.co.nz/index.php/vm...l-products.html

I think I will be going with the 264 with 9.35 lift because the engine only turns to 7300rpm MAX and has stock balancer and a N1 oil pump, or should I go 270's??

So cheers to the guys at Kelford Cams & Boost Magazine, my car is finally going to get some cams. Will do some install pics and before after Dyno Sheets to send back to kelford for feedback.

HL182_A_Camshaft_492bb66580485.jpg

Link to comment
https://www.sau.com.au/forums/topic/268855-won-a-set-of-cams-for-my-rb30det/
Share on other sites

yeh we have 264 and 272 also...Works well.

Congratulations mate...I bet you feel awesome! Nothing quite like winning shit...especially car stuff and ontop of that real performance car stuff!!! Fark im jealous now!

cheers ppl.

I am going to stick with the 264's. I do not rev this car so the smaller the better.

I was going to race the car this weekend but I will put it on hold untill the cams are in!

I aint sure I even needed the extra power but this is going to be a great test!

how much difference would the 270's to the 264's be

seeing that the lift is the same then it would be just change the revs where the power cuts in. I need the power to cut in as soon as possible.

Unsure if you have modified the inlet yet but with a nice exhaust manifold and inlet manifold mid 260's make their peak power around 7000rpm.

Look at Al's RB30det for example, nice inlet and exhaust mani with baby 256 cams but that too also holds well to 8000rpm and with some absolutely ripping mid range.

Mine with 265's idles baby smooth but if slightly leaned out on idle it will start to cam over 'slightly'. So tune it slightly lean on idle and then enable the o2 to pull it in when you want it to idle smooth. :D

Mine went from ~14degree's on 17psi to ~20-21degree's at peak power and made an extra ~30rwkw on pump.

Went from nosing over after it made peak power at 6000rpm to holding power flat for an extra almost 1500rpm, when tweaked with gears peak power is up 500rpm and still holds just as well with no loss in power to 7500rpm (my limiter is also at 7300rpm as Im still running the factory balancer)

The ramp rate on my 265's are a little more aggressive that the grind you will be getting

Mine have 227.9 degree's at 1mm vs 216degree's at 1mm for yours so mine run a ramp rate similar to their 270degree grind.

hrmm.. In stating that I'd almost be inclined to run the 270's. ;)

Edited by TheRogue

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
    • After @Kinkstaah debacle, I'd never want to try and get it right 😛
    • The hood lines up with the fenders. The front bar doesn't perfectly line up with the fenders where the wheel arch is. You have to 'squeeze' the front bar 'in' as it wants to naturally flare out and be longer on the sides. There's a few threads where people notice this when they only swap a GTR style bumper and front bar. Unless you have genuine OEM items - you may be better served getting conversion kits. There are GTT bumpers to fit GTR hoods. There are GTR hoods (non genuine) to fit the GTT bracketry. MAY  
×
×
  • Create New...