Jump to content
SAU Community

TYRE FAIRY's ENGINE HOLDS TOGETHER TO TAKE OUT DYNO COMP

APA

By APA,
in Western Australia

 Share

Recommended Posts

NO_RSPECT Mentor

NO_RSPECT

Posted
Posted

sweet az cuzzy bro

good work buddy, heck and you shaved, ditched the cap and combed your hair. I knew something special was in order

take care.

will call you about the plates or if you wanna leave them with simon the flame thrower i will grab em during the week and leave him the cash

GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

Thanks guys, I was happy with the result and the fact that the car is still running, it must be due to all the praying you all did:D

Thanks to Steve for tuning the car so that it didn't break, and Ray for putting the new turbo setup on. I don't do much to deserve the credit except pay the bills:D

I will be putting forged pistons and rods in as soon as possible, and aiming for 500rwhp at next years show:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...