Jump to content
SAU Community

Recommended Posts

OK to start with here are my upgrades before the Piggyback.....and also a big thanks to the all guy's at Envy imports for putting up with me today.

Powerduct(lol)

Air Fliter Element

Highflow GT30/71 with Garrett BB set

Dump pipe

Manual bleed valve

Standard tune is shown in Green.....the Standard ECU was taking over the piggyback at 5,750rpm.....hence the abrupt end at 164KW's....if it ran all the way to 6,500rpm's it would probably go to 170kw's.

Dyno tune is in Red. PSI has been lifted to 18psi but still bleeds off to 15psi. Response has only been shortened slightly out of the hole. Power is delivered a bit smoother. The biggest problem I had was how much power was lost through the standard intercooler after a run(approx 20-25kw's). The other small problem was wheel diameter.....the non AR-X's will always make more power because of this. Fuel economy is awesome... normally I get in between 5.8 to 6.2....a 50km run in peak hour saw 8.8 and that was with a couple of squirts. Oh and no problems at all with fuel.

So upgrade advice before tune with the mods above.....a good sized intercooler(does not need to be huge though) and a good electronic boost controller and smaller diameter wheels.....then you may see 210 to 220KW's everytime

post-37023-1249291278_thumb.jpg

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

nice!

after going for a drive in Dannys the other day i cant wait to get stuck into modifying the m35.

hows yours going with the ecu and transmission?

i think you've confused me about the "the Standard ECU was taking over the piggyback at 5,750rpm" bit..

nice!

after going for a drive in Dannys the other day i cant wait to get stuck into modifying the m35.

hows yours going with the ecu and transmission?

i think you've confused me about the "the Standard ECU was taking over the piggyback at 5,750rpm" bit..

Transmission is fine......just gotta make sure I put in the right fluid in future though :)

Don't worry...I am just as confused as well!....but thats what I was told.......we never did another run with the standard ECU settings so this is the only one I could show and give you a ruff idea of where we came from.

Edited by Jetwreck
So upgrade advice before tune with the mods above.....a good sized intercooler(does not need to be huge though) and a good electronic boost controller and smaller diameter wheels.....then you may see 210 to 220KW's everytime

So you hit your target of 200awkw then (or am I reading it wrong?).

If so... Very nice mate! Well done!! I guess the turbo makes all the difference... who would've thought?

Already have a custom FMIC template designed by PWR which will suite the M35's quite nicely I think... but at $850, it won't be going in any time soon. :)

Again, great to see your results... No us high flowers have something to aim for :)

I had a similar problem with the Emanage, the ecu would kill power early if something was out. It may have been the airflow meter?

So when are you getting the boost controller...:)

Must be quick now, how is the gearbox taking the power?

I had a similar problem with the Emanage, the ecu would kill power early if something was out. It may have been the airflow meter?

So when are you getting the boost controller...:(

Must be quick now, how is the gearbox taking the power?

Boost controller will be a while.....and the gearbox should hold for a good amount of time I hope.....if I buy anything else it will be an intercooler(sway bars and Nismo stickers on the way)

My problem at the moment is that my wife has no idea that I have received and already spent my tax return.....I am so dead when she finds out how much I got back :) !!!!!!.....whats the worst she can do?......take the sex that I am not already getting off me?????.......or then again she might sit me down and make me listen to her :)

Edited by Jetwreck
I'd say f**k your wife, it's your money after all. Well that's what I said to my bitch at least.

Gold!!!!! :) ....does your wife get on these forums much??? :)

PS. 5 minutes away from leaving work from my first real squirt with no traffic.

Edited by Jetwreck

lol craig let us know how it goes :)

sorry no luck....bugger bugger bugger.......followed all the way down Beecroft RD by police only to be pulled over at Pennant Hills shops and breath tested.....it's a conspiracy!!!!

sorry no luck....bugger bugger bugger.......followed all the way down Beecroft RD by police only to be pulled over at Pennant Hills shops and breath tested.....it's a conspiracy!!!!

Dammnnnn

im really REALLY jealous now. i want to break my turbo and install a hiflow and be forced to put the emanage on lol

Me too - despite the expense, I'm kinda *hoping* for a reason to install an HKS GT-RS on my s1 C34, then turn it up to about 15psi.

It's already got around 167rwkW on 7psi and 184rwkW on 10psi, so 200 at ALL wheels shouldn't be too far off!

Mods so far:

- Walbro fuel pump;

- GReddy FMIC;

- APEXi PowerFC;

- GReddy Profec-B Spec II boost controller;

- Bell-mouth front/dump pipe

- high-flow catalytic converter

- 3" exhaust

I'd say f**k your wife, it's your money after all. Well that's what I said to my bitch at least.

She was prolly interstate. If she really finds out you will be intestate. :)

Boost controller will be a while.....and the gearbox should hold for a good amount of time I hope.....if I buy anything else it will be an intercooler(sway bars and Nismo stickers on the way)

My problem at the moment is that my wife has no idea that I have received and already spent my tax return.....I am so dead when she finds out how much I got back ;) !!!!!!.....whats the worst she can do?......take the sex that I am not already getting off me?????.......or then again she might sit me down and make me listen to her :)

Which intercooler are you looking at? Full kit or custom unit??

The worst she could do is have her mother move in for "moral support".

I'd say f**k your wife, it's your money after all. Well that's what I said to my bitch at least.

1. Indeed. Isn't that part of the deal?

2. Yes. Yes it is.

3. In those words? Suuuuure.

Boost controller will be a while.....and the gearbox should hold for a good amount of time I hope.....if I buy anything else it will be an intercooler(sway bars and Nismo stickers on the way)

My problem at the moment is that my wife has no idea that I have received and already spent my tax return.....I am so dead when she finds out how much I got back :) !!!!!!.....whats the worst she can do?......take the sex that I am not already getting off me?????.......or then again she might sit me down and make me listen to her :P

Haha just tell her you cant multi task are trying to breathe, cant listen and breathe at the same time now can we! haha

hhhhhmmmmmm!!!!

Wife just found out the I have received and already spent my tax return...........there was a very long pause on the phone followed by " I am to pissed off to talk to you right now.....we will chat when I get home"

Options guys.....HELP!!!!!!

Option one: Get drunk before I get home!

Option two: Don't go home

Option three: Flowers and chocolate

Option four: Find new wife

HELP.....please!!!!! :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...