Jump to content
SAU Community

Recommended Posts

I am sorry if this is posted in the wrong section, but I wasn't sure where is the best place for this.

This pump should generate a couple of hundreds of PSI so it is fairly forced inducted :)

I an looking at converting the old hydraulic pump to an electrical system. I am still not sure what pump to get but I read somewhere that the pressure generate is somewhere in the vicinity of 850+psi or something. How reliable is the electrical pump for this job?

What pump have you used? Any maintenance/failure? Which pump is reliable?

Could you please snap and share some pics of your setup?

Why on earth would U want an electric power steering pump?

It'd put a huge load on the alternator and cause the same or more resistance to the engine because the alternator and electric pump aren't 100% efficient. I see no advantage.

Just to name a few

-more space in engine bay

-better weight distribution

-don't have to worry about the belt

-don't have to worry about over hearing p/s fluid

So do you know much power the electric pump will rob off the engine?

Theoretically the same amount of power it robs off it in mechanical form, plus another 20-30% in the energy conversion..

The pump itself weighs like >1kg so that is hardly going to effect weight distribution a worthwhile amount and the belt is $20 and lasts forever..

The only advantage I could see is you could increase WOT power and engine response by the slightest amount as the engine doesn't have to deal with spinning the weight of the pump more than it has to anymore..

I guess if you needed the space to bolt one of those supercharger kits or a dry sump pump there it would be feasable, but for shits and giggles I think it really is one of those pointless mods, up there with the electric supercharger IMO :down:

EDIT: If you're still keen though the item from a Toyota MR2 seems to be a pretty cheap and popular choice..

Edited by aphid

Yep I'm putting an electric power steering pump in the new race car, I know Risking is running one in his as well.

I'm looking for easier maintenance, simpler motor/balancer, better placement of the pump and resoviour. And the standard mechanical system boils easily under race conditions

And remember the PS pump is not running all the time, and you are unlikely to be pulling more amps than the alternator can provide...ie no additional drain on engine power.

+1 for what duncan said! Plus all the extra space to get to the dry sump pump right underneath it! Also, as 9krpm said, one less belt to worry about. Which in race conditions can come off. It normally creates dramas when its just behind your dry sump pump belt!

Clearly this is not for road going cars....

ahh yes thanks....I meant to mention that the astra pump is the one most often recommended. crack can you ring holden with the vin and get me a part number :D

Like Michael said its a race car only thing, too much trouble for little gain in a road car, but worth looking into for a race car. If it helps GT cup cars run electric power steering which is good enough for me, they are the best touring race cars in the world.

Brad is running a custom/race one from tilton? earls? someone. Very good feedback on it's consistency whereas the standard one doesn't last 10min racing even with a cooler, let alone the 1hr races we do

  • 5 months later...

Yeh what dave said.

Im curious as I may need to source one to aid in my supercharge project. The one ive sourced before is on back order from that company and its pretty exxy. It would be nice to have a couple of options.

I was thinking about something like this, electric powered pumps for the oil/water/pwr steering etc would mean not having to worry about the water pump cavitating at high revs, better oil control?

Just set one up today on a dirt track car.

Using the holden astra/ suzuki swift/ opel euro box electric setup.

t is not an electro hydraulic system. It is an electricalls assisted manual rack. There is a load sensor in the column which tells the motor to drive.

2 inputs are required from the car, rpm and speed. The rpm can be tricked with a small frequency generator to simulate a running engine, and the speed input varies the amount of assist you get from the motor. On the sprint car we put an adjustable pot on the frequency generator so we will have 5 levels of assist to try when we get to the track.

It works very well so far, not tested under race conditions, but the assist is very powerful.

There is also a pot in the booster motor which can be adjusted to increase or decrease the feedback to the driver. Max current draw about 45a if you load it up.

i can get some photos if anybody is interested

The mr2 setup is good if you are retaining the manual/hydraulic rack. You need to make sure you get the controller and set it up correctly. Many people just hook the pump up to 12v and its humming away all the time drawing a lot of current.

Ive been trying to source an MR2 one from wreckers today. I rang a few but no one has any. Dont suppose you have one Trent?

A new one from Toyota is $1400.

Edited by r33_racer
Duncan did you end up sourcing one and fitting it?

no sadly....that project is very much on ice, and will be for another 12 months. Not canned...but very stopped right now. Would be good to hear what you find

Trent, MR2 or MR-S? either way I guess I am unlikely to find one. what current do they draw

Well i finally won one today from ebay of all places. A bloke in the USA had one off a 2002 Spyder. Apparently alot better then the older units as it has the electrics built into it. One unit, pump, tank and controller. Hopefully should have it within the week. I will keep this bit updated with how it turns out. If not it will be in my supercharger thread as I get it done and documented.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...