Jump to content
SAU Community

Recommended Posts

G'Day,

I've been looking at the "BC Racing" coilover for sale on ebay, they have external reservior, shock and rebound adjustable , body height adjustable for $1695.00. They look the goods but seem way too cheap.

I looked up their website, they are from the UK and have some sort of German accreditation, but I assume they are manufactured in China. "Not that that a bad thing", I don't want to end up in a jail cell with a Rio Tinto Executive.

Has anyone bought these?

Any comments

I just had Centreline Suspension in Melbourne install them in my 180sx. When i picked my car up, i was asked what i wanted to do with the car. I was basically explained that these coilovers (ER model) are made for track usage. So far I haven't driven my car much (issues with alternator)

they look quite good for $1700 delivered but there is no way to tell what they are like till you test them. many compaines just make 1 damper and use different fittings on the ends to make it fit many different cars. this is bad as different cars and different springs and different useage needs different damping specs and different valves and shim stacks inside the damper. there is no way to know what is inside a damper you buy (without getting it on a shock dyno or pulling it apart) and no way of knowing what kind of R+D has been done to make that damper work with your specific model of car. in the case of most stuff manufactured in china and taiwan the chance of them having done extensive testing on say an R32 GTR is pretty slim, where as compaines like tein etc do that testing. there is the same issue with springs but it's not such a big deal as spring rate are fairly easily and cheaply changed. the other issue of course is quality. it's no use if they work well if they spit out a seal in 6 months time.

all of these things are un-known. of the problems the biggest one is the damper. many of those companies just use very 'approximate' specs for the damper. at most they might look up the weight and F-R weight balance of a car on the net and have a guess from there, but I highly doubt they have tested every model they make on the actual model of car it's made to fit.

i believe BC also make Racing Logic Coilovers? I've heard great things abt those coilovers, just not many reviews on the "BC" labelled ones.

If BC have anything to do with Racing Logic dont buy them, i was given set of new Racing Logic Coil overs to test in my R32 GTR, had them in for 4 months after trying differant springs, they are crap,

way to bouncy under brakes over bumps and dampers where up shit creek, let alone did very

little when adjusted.

Now have Tein Mono Flex and fells like a differnat car.

Spend the money and buy the good stuff....

Legnum/EVO boys love BC Coilovers, my friend bought the BC BR range for his Legnum, not bad for the price, but then again none of my mates have another Legnum to compare to.

ill have a set of these in my R32 GTR race car for the next meeting.

They are being checked and tested right now before we fit them up.

Ill be keeping my old spring rates and going from there so after some testing ill be sure to post up results

meh for the money I'd rather have a decent shock / spring combo (don't really care for adjustment on a street car)

I bet they are harder than a cat's head lol, especially if someone was told that they are good only for track use lol

I am also contemplating on this BC Racing (BR spec) and Tein Super Street. Hope to hear more feedback for on the track and street experienced for r34 GTT. The spring rate for the BC Racing (8/6kg) is slightly more than the Teins SS (6/4kg). However the BC is monotube against the Teins twintubes. Appreciate feedback and if there is any comparison between both models.

ill have a set of these in my R32 GTR race car for the next meeting.

They are being checked and tested right now before we fit them up.

Ill be keeping my old spring rates and going from there so after some testing ill be sure to post up results

Are you getting the shocks dynoed? If so I'd love to see the graphs.

Been trying to get BC & GReddy to cough them up without success and haven't had time to pull my GReddys out to test.

Are you getting the shocks dynoed? If so I'd love to see the graphs.

Been trying to get BC & GReddy to cough them up without success and haven't had time to pull my GReddys out to test.

Hoping to know more about the BC on Skylines although other forums espescially the Evo/Subaru seems to like them very much. So far they have the BR specs with option of rubber or steel topmount to choose. Too bad there is no external reservoir type made for the GTT other than Evo/Subaru.

  • 1 month later...

I have also been looking at ther BR ones on ebay, they are a pillow ball upper mount. however i noticed in some ebay sellers fine print they are seling them withouth the rubber pillow mount. so be careful on that one. other than that i have heard only good things about them.

  • 2 months later...

i run greddy type s with 8/6 springs.

these are aparently the exact same as the bc ones

my car makes 323rwkw and also has struts, sways, pineapples, castor, camber and mech diff.

the coilovers are run @ 320mm centre to guard (low)

tyres are nitto NT05 245/40/18

i get traction through all gears right through to 7.5k rpm when i mash the loud pedal, and only spin when i want them to.

there is zero axle tramp.

they are a comfortable enough ride and my car is my daily with the coils on the hardest setting for nearly 2 years now.

the only thing they are shitful for is launching, but hey, its an 8/6 combo... that's just what you have to put up with

i am very happy with the product for the money and would happily buy again

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...