Jump to content
SAU Community

Recommended Posts

I pulled out my passenger seat to put in a GTR seat I just bought, and saw this box kinda thing coming out of the carpet with a plug that must have been plugged into something once. Does anyone have any idea what it is? I am very curious

post-63044-1253066669_thumb.jpg

not sure have a similar thing in my r33 s1, not sure whats it's for. I had a bit of a poke around with the multimeter with the interior light on, then the doors open, and with engine running and i couldn't detect any current.

I've got a SII Gtst and it has both drivers and passenger seat belt warning light harness, plus a cat temp sensor, so could be either, but I'd say seat belt. Logic tells me a cat temp sensor wire would be too bloody hot to go anywhere near flamable materials for at least a metre or so until it cools enough.

If it's the same as a R33 it's the plug for the cat temp sensor. The drivers side has the plug for the seatbelt.
If the car is a GTR, cat temp sensor, non-GTR who knows, most likely the seatbelt (I'm fairly sure only the GTRs have cat temp sensors?)

+1, cat temp sensor.

you can see that it has a stainless braid outside which is required for the heat resistance

nothing...unless its plugged in :D

it warns of high temp in the cat - ie cat blocked.

Yeah but where is the wire it plugs into!! Mine is the same as Pic with the tail but No connection to connect it into!!

Oh and what is that vent thing???? Been wondering about that to!

I checked after someone mentioned it was for the seatbelt and sure enough there is the other half of the plug coming from both the GTR seat and the GTS-t seat i pulled out, but I havent plugged it in yet. I might try tomorrow and see what happens.

Well I plugged it in and nothing happened, how anti-climatic. Kinda seems pointless. I also saw the cat sensor wire with the braided line nearby people were talking about.

I have no idea what it is but ill tell ya a funny trick

If ya fit airhorns under your passenger seat and wire it up to your glovebox

Then when casually cruising along with a friend oneday you ask them to get something out of the glovebox...

Absolutely priceless

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...