Jump to content
SAU Community

Recommended Posts

Just fitted the GT3076R to an RB25/30.

Engine management is Haltech S2000, closed loop boost control.

Turbo kit came with standard Garrett 5psi actuator.

Can only peak briefly at 18psi then drops to 15. 310 rwkw max.

Really would like 330 - 340

Another example here is Als. Pretty much a similar engine to mine, injector sizes, cams, only he opted for the 15psi actuator.

However Al only gained an extra 2 psi across the graph, and our curves are identical, same peak and drop, but he's got 20 kw more.

Is this the typical symptom of the IW 3076 ? or is it still crap actuators ?

If I was to fit a large can 18 psi actuator, could I achieve 21 psi flat line.

Also wouldn't mind boost to come on a little earlier

Please don't tell me to go External wastegate.

Cheers.

post-25026-1253702421_thumb.jpg

post-25026-1253702434_thumb.jpg

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

i think hes refering more to the boost plot than the power. try a heavier actuator, i've got a 12psi with a profec b and can hold 22psi fairly well. make sure you wind in as much preload without restricting the full opening of the gate too

I switched to a 0.9bar actuator on my GT30 IW and it held 20psi well on the dyno, but has been set to 16psi by my tuner (thru the EBC). Ideally you want to run an actuator pressure as close to what you want to run. Find yourself a 1.4bar actuator....

Well I've got the sorta the same problem from my tune. The boost would only hold up to 1.1bar and wouldnt hold at 1.2 or 1.3... I'm thinking its the boost controller thats the problem but the tuner reckon its wastegate.

Well I've got the sorta the same problem from my tune. The boost would only hold up to 1.1bar and wouldnt hold at 1.2 or 1.3... I'm thinking its the boost controller thats the problem but the tuner reckon its wastegate.

What RPM is your peak boost?

However Al only gained an extra 2 psi across the graph, and our curves are identical, same peak and drop, but he's got 20 kw more.

Dyno differences more than anything else if its only 15-20rwkw.

Move the boost pickup to the cold pipe instead of the hot pipe if it isn't already. This helps reduce boost tapering down. Also GT3076R's are designed for low boost with their T04E 0.6 compressor housing so i wouldn't go higher than 19psi or so on one anyway. Try to get it to hold 19psi with the pickup on the cold pipe.

If you want the most out of that turbo you HAVE to run the the largest 1.06 A/R ratio turbine housing . Others with these turbos on twin cam RB30's for some reason fear turbine lag with this housing and I can't understand why . Some have said that these engines are a bit laggy with a 1.06 turbine housing on a GT3582R but thats largly because the GT35 turbine is 8mm larger on the OD and a fair bit larger on exducer size than the GT30 turbine .

I know 8mm doesn't sound like much but do the area of a circle calcs and you soon work out the difference is significant .

I can't tell you what the boost threshold difference is between a 1.06 A/R GT3076R and a 1.06 A/R GT3582R but the wheels are larger and heaver in the latters case . The other thing is that the GT30 turbine has been designed to work with a GT30 turbine housing as a matching pair , everything I see points to the GT3582R's using a bored out GT30 turbine housing so not exactly an ideal situation . Real GT35 turbine housings from the diesel world start at about .96 I think A/R with the twin entry T3 like Euro T4 flange and grow to about 1.17 + A/R with the large T4 international TS flange on turbos like the GT3576 .

If I wanted a reasonably free reving RB30 twin cam and 320 + Kw I would have no hesitation at all in running the big housing on a GT3076R , big engine with big exhaust flow requirement needs a bigish turbine housing to cope with it .

I'm not so sure the GT3076R is a "low boost turbo" because it wears a T04E compressor housing . I don't think the beginnings of gas flow restriction start with the compressor housing , I reckon its all in the turbine housing . The fact that they come std with a port shrouded compressor housing shows that Garrett knows the compressor will potentially surge with small and possibly medium sized turbine housings .

Both wheels in the over the counter GT3076R are big on trim size - 84 for the turbine and 56 for the compressor and this is not something added to give stellar turbine response . It's done to maximise gas throughput for the basic size of each wheel .

If really serious with three litres forget all about these small frame GT BB turbos , step up to a split pulsed T4 flange manifold with two external gates and bolt on a GT4088R . Arguably one of the best dedicated petrol engine performance turbos Garrett ever made .

Your calls , cheers A .

get a higher pressure actuator . its never gonna work properly when your target boost is over 4X your waste gate pressure

duty cycle would have to be massive if not 100% depending on your plumbing . and changing 1% will have a massive effect due to massive difference between actuator pressure and target pressure

If you want the most out of that turbo you HAVE to run the the largest 1.06 A/R ratio turbine housing . Others with these turbos on twin cam RB30's for some reason fear turbine lag with this housing and I can't understand why . Some have said that these engines are a bit laggy with a 1.06 turbine housing on a GT3582R but thats largly because the GT35 turbine is 8mm larger on the OD and a fair bit larger on exducer size than the GT30 turbine .

I know 8mm doesn't sound like much but do the area of a circle calcs and you soon work out the difference is significant .

I can't tell you what the boost threshold difference is between a 1.06 A/R GT3076R and a 1.06 A/R GT3582R but the wheels are larger and heaver in the latters case . The other thing is that the GT30 turbine has been designed to work with a GT30 turbine housing as a matching pair , everything I see points to the GT3582R's using a bored out GT30 turbine housing so not exactly an ideal situation . Real GT35 turbine housings from the diesel world start at about .96 I think A/R with the twin entry T3 like Euro T4 flange and grow to about 1.17 + A/R with the large T4 international TS flange on turbos like the GT3576 .

If I wanted a reasonably free reving RB30 twin cam and 320 + Kw I would have no hesitation at all in running the big housing on a GT3076R , big engine with big exhaust flow requirement needs a bigish turbine housing to cope with it .

I'm not so sure the GT3076R is a "low boost turbo" because it wears a T04E compressor housing . I don't think the beginnings of gas flow restriction start with the compressor housing , I reckon its all in the turbine housing . The fact that they come std with a port shrouded compressor housing shows that Garrett knows the compressor will potentially surge with small and possibly medium sized turbine housings .

Both wheels in the over the counter GT3076R are big on trim size - 84 for the turbine and 56 for the compressor and this is not something added to give stellar turbine response . It's done to maximise gas throughput for the basic size of each wheel .

If really serious with three litres forget all about these small frame GT BB turbos , step up to a split pulsed T4 flange manifold with two external gates and bolt on a GT4088R . Arguably one of the best dedicated petrol engine performance turbos Garrett ever made .

Your calls , cheers A .

Compared to a GT3071R, i think it's a low boost turbo. If u look at the differencer between the compressor maps of both, the 76 has wider lower islands where the 71 has higher narrower islands.

I prefer to look at the number of corrected pounds of air that the compressor is pumping , if anything the lower the boost pressure is for a given air flow rate the less the outlet air temp tends to be .

For what ever reasons the real GT3071R didn't end up being the more responsive little brother to the GT3076R that many of thought it would be . I think Garrett attempted to make a production version of their competition spec TR30R turbo and it didn't really work out because unlike the TR30R's 60mm NS111 turbine (in 73 or 76 trim) the 60mm GT30 turbine is 84 trim and 10 bladed instead of 9 .

It makes life hard trying to get more or I should say earlier response with a big trim turbine by using a smaller A/R turbine housing , I reckon what happens is that the smaller volume volute passage gets the gas speed up and the larger aspect ratio exducer side loses much of it .

HKS seemed to get around this best by using the cropped version of the GT30 turbine in a GT30 based turbine housing with the GT2835 series turbos - not the GT28 turbine housing versions of them . Out of this I think they got a bit higher shaft (compressor) speed without necessarily using small ratio turbine housings . Garrett chose to only use these cartridges in GT28 turbine housings for their marketed range and we know they're a POS turbo in that form .

If they'd given us the 60mm NS111 turbine from the TR30R and profiled their GT30 turbine housings to match then the "GT3071R" would have been a more responsive and successful turbo IMO .

The TR30R turbos had either a 76.2 or a 69.something mm compressor wheels in a couple of trim sizes . The largest comp option that I've seen a map for is dimensionally similar to the GT3076R's 76.2mm 56T wheel but it is of a different family and if I remember correctly is 5/5 bladed rather than 6/6 like most GT series wheels .

A .

Anyone fitted the HKS actuator to one of these ? Any better than the Garrett 18psi large can.

Nengun have a small range of high boost actuators.

All a bit pricey though.

I've decided to go the 18psi unit as I never really ever turn it down.

Also wouldn't mind it to come on a little earlier.

Again Haltech controls it closed loop.

Cheers

Anyone fitted the HKS actuator to one of these ? Any better than the Garrett 18psi large can.

Nengun have a small range of high boost actuators.

All a bit pricey though.

I've decided to go the 18psi unit as I never really ever turn it down.

Also wouldn't mind it to come on a little earlier.

Again Haltech controls it closed loop.

Cheers

I have a Haltech E11v2 with a boost controller solenoid, my GT3076R (3037S) has a 12psi actuator. How well is that going to control boost? I shall be finding out later this week when i get it installed and tuned, just wanting to know what i should/shouldn't be expecting.

One really has to drive the GT3076r with a .82 rear on the RB30 to understand why it is such an awesome combination.

Al's has no issues pulling out to 8k with his .82 rear. Power is limited to around 320-330rwkw on pump with the .82 rear.

The 1.06 gt30 hot side flows approximately the same as a GT35 .82 hotside however the gt30 comp wheel is wasted on it as it runs in to choke well before the hot side is max'd. For a track car sure.. It will help keep EGT's down but for a streeter its best to tighten up the scroll.

Spool is similar between the gt30 .82 and 1.06 GT30 so I really wouldn't bother. A leaf out of the RB30ET's... They simply skip the whole 1.06 rear on the GT30 idea as the gains are minimal for the increased lag.

--

On Topic.. Even the GT35r IW's have issues holding boost regardless of power being made. Back to SK's ideals... Match the wastegate to the boost you wish to run. In my experience its best to try to get the actuator to around -2psi of the total boost you intend to run.

Edited by SLAPS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...