Jump to content
SAU Community

Recommended Posts

I was giving the thumbs up to a nice black R35 with boost mobile stickers on it this arvo going under the runway and then saw a nice R33 GTST with a black bonnet in the tunnel.

no way!

I saw 140 clean + shiney skylines (plus matt's one) at Fairfield showground today. Literally everything from KGC10 to R35

hahah "plus matts one" - did he shine up the paint chips so the under finish was nice and shiny at least :)

best time was 15 :) ... found out clutch was organic :P lol... how bout u??? saw ya lined up a few times

Haha yeah sames.. best time was only a 14.2 :P ... realised it had a vaccuum leak though when we stopped on the way home lol

Haha yeah sames.. best time was only a 14.2 :) ... realised it had a vaccuum leak though when we stopped on the way home lol

I was out the same night and ran a 12.0, i think i might have even run against you on one of the runs?

I was out the same night and ran a 12.0, i think i might have even run against you on one of the runs?

hey man u werent the 1 i was talkin 2 with the same dash as me lol???

Spotted YLDDR30 (his SAU name) in the red DR30 with the RB singing on Friday arvo in Castlecrag (Eastern Valley Way).

Dont think you saw me but I was heading north in my DR (getting its monthly exercise. Must be the first time in a long time 2 DR30's have crossed paths in NSW.

cheers

that be me, carnt believe i missed another dr30! damn! i always seem to miss u

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...