Jump to content
SAU Community

Recommended Posts

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

Is a C210 acceptable for this drivers day?

Absolutely!!! Hell it would be great to see an old school machine out there!

In the past we have had stock standard Pulsars, Hyundai Excel, Ford Focus and other 'non race car type cars' enter the event....so your C210 is more than welcome. If you wish to enter, drop me a pm. :no:

Hope to see you out there.

Brad,

As discussed, please put me down for my two sons as well. If we are careful, the car will get a bit of a rest between runs!

I will send through payment for two non-members.

Cheers. :)

as for people who are wondering about if your car has a yellow sticker can you compete. yes you can so long as it is not for saftey you will need to orgainse to call ashleigh at rac driver center and give her details of sticker and they will tell you if its ok or not, but in saying that it will still have to pass the instructor on the day, it just helps to have the go ahead from management before you get there. I have done this and i am able to use my car when i go next time

List is updated. A few spots left. :laugh:

Brendon, Flash, Cheers for the payment. Dan will mark them paid when he sees it (if he hasnt already).

Reaper...thanks for the info!! Hope that clears up the question :cheers:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...