Jump to content
SAU Community

Recommended Posts

50k + super

Was aiming towards 55k + super as one survey shows that as the average grad salary

that's not bad for grad. some of my mates got shafted with a 45 + super for grad positions... employers were pretty much like "you want a job, you play by our rules, otherwise we'll just give it to someone else." so now they're just gaining experience and as soon as they get a better offer, they're outta there.

anyone of yoouse guise good with a welder?

32's getting stripped down and redone in all factory panels n stuffs... with a gangster twist.

they're only paying you 50k cos you went to Monash Pat :)
haha actually, now that you mention it, all the mates with shitty grad pay went to monash too :)

La Trobe FTMFW.

anyone of yoouse guise good with a welder?

32's getting stripped down and redone in all factory panels n stuffs... with a gangster twist.

haha actually, now that you mention it, all the mates with shitty grad pay went to monash too :)

La Trobe FTMFW.

Postera Crescam Laude*

that's not bad for grad. some of my mates got shafted with a 45 + super for grad positions... employers were pretty much like "you want a job, you play by our rules, otherwise we'll just give it to someone else." so now they're just gaining experience and as soon as they get a better offer, they're outta there.

haha sounds about right. Ill see how it plays out. The HR manager told me in July they give out wage increases, so i guess ill see what happens there.

they're only paying you 50k cos you went to Monash Pat :)

haha id rather be an underpaid monash grad than a melb uni grad. You lot are only good for cleaning my car :)

anyone of yoouse guise good with a welder?

32's getting stripped down and redone in all factory panels n stuffs... with a gangster twist.

haha actually, now that you mention it, all the mates with shitty grad pay went to monash too :)

La Trobe FTMFW.

i like where this is going.

i can tig weld funky. but it isnt pretty :)

well the idea is to go back to all metal panels, stock bodykit which is shaved and plastic welded etc.

gonna cut the metal guards up, then chuck em under the rollers to give em different curves and seams. weld in a "boser style" front on the stock GTSt bonnet too.

basically what the euro boys do with golfs, done to the 32.

to finish off i'm gonna chuck 18x10" all around and dump it on its guts.

i'll keep stock suspension on hand if i get defected. not gonna rego the camaro, i'll just drive it on trade plates :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...