Jump to content
SAU Community

Recommended Posts

the dude that owns JZX100 works in one of the places near my shop

pretty much watched that thing go from daily to part time tracker to fully stripped screamer, straight pipes and all.

is tough

So any phone geeks (Shan, I'm looking at you) able to help me?

Been offered a HTC Desire HD to replace my iPhone 3G... yay or nay? I'm a bit over the iPhone, so wouldn't mind trying an Android or W7 phone, but yeah...need some more smarterer advice.

only tards buy Verossas. Chaser/Cresta/Mark II is where it's at.

cimg7028tig5.jpg

110_6.jpg

110_8.jpg

JZX110_MarkII.jpg

besides, verossas aren't allowed for import on account of them looking like a dugong. True story.

http://www.j-spec.com.au/wiki/Toyota/Chase..._only%29/id-514

then again, most skyline drivers cling to the 90's like it wasn't 20 years ago.

The Rise, lay it on me..

well not certain but i'd think it will be similar to most areas ie. pretty sh*t at peak times.

unless they have upgraded the exchange but i doubt it.. most ppl go for wireless

Shan, what's a good amount of negative camber for my fronts? Just wanna get some figures so I can tell the wheel alignment guys when I finally get around to getting it done :D

none. you have a snap heavy mid engined RWD car. any negative camber on the front and not the rear will make it even more snap oversteer prone.

it'll be like driving a loaded slingshot being head by a sweaty finger.

have fun with that.

its all the one car now right?

the slashes aren't fuckin ornamental. Different cars, different parts, same chassis, as has been for the last 4 generations.

If I wanted to please people here I wouldn't have bought an MR2 :D Coz y'all hate them.

But Shan is right about the mexican fronts. Doesn't look so good. Popo wouldn't like it either.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...